AER AG 83 사용자 설명서 - 페이지 13

{카테고리_이름} AER AG 83에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AER AG 83 16 페이지.

페이지 인쇄

6. Technical specifications

line in

Balanced or unbalanced line input

Combo socket, XLR + jack ¼" (6.35 mm)

Nom. input voltage:

Min. input voltage:

Max. input voltage:

Input impedance:

Signal/noise ratio (A-weighted):

Equivalent input noise voltage

(A-weighted):

Phantom power (optional): 9 V DC /

max. 100 mA, on ring of input jack,

short circuit protected.

External equipment may be damaged by inappropri-

ate use of phantom power.

Make sure you use a mono jack connector and cable

whenever the 9 V phantom power is not required.

aux in

Auxiliary stereo input, e.g. for CD

3.5 mm stereo jack socket

Nom. input voltage:

Min. input voltage,

stereo:

mono:

Max. input voltage:

Input impedance:

Signal/noise ratio (A-weighted):

Equivalent input noise

(A-weighted):

mic in

Balanced microphone input

Combo socket, XLR + jack ¼" (6.35 mm)

XLR (balanced), stereo jack (balanced), or mono jack

(unbalanced)

1 / sleeve = ground,

2 / tip = positive (+),

3 / ring = negative (–)

Nom. input voltage:

Min. input voltage:

Max. input voltage:

Input impedance (balanced):

Input impedance (unbalanced):

Voice filter:

Signal/noise ratio (A-weighted)

Equivalent input noise voltage

(A-weighted):

Phantom power (XLR only):

Supply resistors:

Load current:

clip indicator

Headroom:

line out

Preamplifier output after tone controls

and master

Mono jack, ¼" (6.35 mm)

Nom. output voltage:

Output impedance:

Min. load impedance:

Residual noise voltage

A-weighted):

pre out

Preamplifier output before tone

controls and master

Mono jack, ¼" (6.35 mm)

Nom. output voltage:

Output impedance:

Min. load impedance:

bass

Influence at 100 Hz

treble

Influence at 10 kHz

Power amp

construction

Monolith IC with DMOS output

rating

Output power (THD = 1%)

Continuous output power is determined by the

limiter, see limiter threshold

500 mV (–6 dBV)

200 mV (–14 dBV)

9 V (+19 dBV)

25 µV (–92 dBV)

500 mV (–6 dBV)

100 mV (–20 dBV)

200 mV (–14 dBV)

10 V (+20 dBV)

> 22 kΩ

24 µV (–93 dBV)

10 mV (–40 dBV)

2 mV (–54 dBV)

1 V (0 dBV)

–11 dB at 300 Hz (referred to 10 kHz)

1.9 µV (–114 dBV)

6.8 kΩ

max. 10 mA

approx. 6 dB

1 V (0 dBV)

4 µV (–108 dBV)

500 mV (–6 dBV)

± 8 dB

±11 dB

60 W / 4 Ω

General

distortion

noise

20 kΩ

86 dB

signal processing

limiter

speaker system

power supply

mains fuse

operating temperature range

cooling fan

cabinet

87 dB

finish

dimensions

weight

Options

Voice filter of mic input can be bypassed by an internal jumper.

Refer modification to qualified personnel.

Definitions

1 kΩ

Rated conditions:

3 kΩ

• nominal input voltage at input under test

• input control adjusted to nominal output voltage at pre out.

74 dB

• gain of unused inputs fully anticlockwise

• master fully clockwise

• bass / treble centered

48 V

Nominal input voltage: Standard condition for specifications,

if not stated otherwise.

Minimum input voltage: Input voltage required for nominal output with

maximum gain and volume settings.

Maximum input voltage: Input voltage that does not cause distortion

more than rated THD+N, suitable control settings provided.

Nominal output voltage or power refers to rated conditions.

47 Ω

THD + N: Total harmonic distortion + noise, input voltage reduced by 10

2 kΩ

dB after setting up rated conditions.

Signal / noise ratio: Ratio of output voltage at rated conditions to output

noise voltage with input shorted.

Equivalent input noise voltage: Noise voltage at loudspeaker terminals di-

vided by gain of amplifier. Input shorted after setting up rated conditions.

Residual noise: Output noise with minimal gain and volume settings.

47 Ω

Adaptive limiter: Adaptive with respect to power supply. Maintains cons-

5 kΩ

tant headroom regardless of power supply fluctuations.

General: Signal voltages are RMS values. Test signal sine 1 kHz sine unless

stated otherwise. Noise measured from 20 Hz to 20 kHz. Noise stated for

a specific input implies that all other inputs are not used. Sound pressure

level (SPL) based on loudspeaker specification by manufacturer.

Specifications and appearance subject to change without notice.

TD20170608 (AG 8/3)

THD + N

Measured at loudspeaker terminals

Residual noise (A-weighted), referred to

nom. output power:

Acoustical:

approx. 14 dB SPL / 1 m

Signal/noise ratio:

Subsonic filter, adaptive peak limiter,

speaker eq with harmonics exciter

Threshold

8" (200 mm) dual cone full-range speaker in bass

reflex cabinet

mains voltage (depending on model)

100, 120, 220, 230, or 240 V~, 50–60 Hz

Power consumption: max. 120 W

Size: 5 x 20 mm

220, 230, 240 V models:

100 and 120 V models:

Temperature controlled

15 mm (0.59") birch plywood

Waterbased acrylic, black spatter finish

Height

Width

Depth

Weight

< 0.1% (6 W / 4 Ω)

–97 dB

see input specs

50 W / 4 Ω

T 1A L 250V

T 2A L 250V

0...35 °C

269 mm (10.59")

335 mm (13.19")

260 mm (10.24")

7.5 kg (16.53 lbs)