Clarion CZ109 서비스 매뉴얼 - 페이지 3
{카테고리_이름} Clarion CZ109에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Clarion CZ109 15 페이지. Cd/mp3/wma receiver
Clarion CZ109에 대해서도 마찬가지입니다: 소유자 매뉴얼 (19 페이지), 설치 및 전선 연결 매뉴얼 (2 페이지)
페이지 인쇄
TROUBLESHOOTING
Problem
Power does not
turn on. (No sound )
No sound when
operating the unit
with amplifiers or
powerantenna
attached.
Nothing happens
when buttons are
pressed.
Display is not
accurate.
No sound.
No sound.
Sound skips or
is noisy.
Sound cut out or skips.
Noise is generated/noise
is mixed with sound.
Sound is poor when
power is first turned
on.
Wrong file name
ERROR DISPLAYS
If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem.
Error Display
ERROR 2
CD/MP3/
ERROR 3
WMA
ERROR 6
If an error display other than the ones described above appears, press the reset button.
Cause
Fuse is blown.
Incorrect wiring.
Power antenna lead is short
circuited,or excessive
current is required for
remotely powering on the
amplifiers or power antenna.
Microprocessor malfunction
due to noise,etc.
DCP or main unit connectors
are dirty.
The speaker protection circuit
is operating.
MP3/WMA files are absent
on disc.
Files are not recognized as an
MP3/WMA files.
File system is not correct.
CD is dirty.
CD is heavily
scratched/warped.
MP3/WMA files are not
encoded properly.
Condensation may form on
the internal lens when the car
is parked in a humid place.
File system is not correct.
Cause
A CD is caught inside the CD deck and is not
ejected.
A CD cannot be played due to scratches, etc.
A CD is loaded upside-down inside the CD deck
and does not play.
Replace with a fuse of the same amperage as the old fuse .
Read the attached "Installation/Wire connection Guide" once again
and wire properly.
1. Turn the unit off.
2. Remove all wires attached to the power antenna lead. Check each
wire for a possible short circuits using an ohm meter.
3.Turn the unit back on.
4. Reconnect each amplifier remote wire to the power antenna lead one
by one. If the amplifiers turn off before all wires are attached, use an
external relay to provide remote-on voltage(excessive current required).
1.Turn off the power, then press the [RELEASE] button
and remove the DCP.
2.Use a thin rod to hode reset button depressed (2 sec.)
If the reset button is pressed when a disc is loaded,
please eject the disc and load it once again before
attenpting to play it.
Wipe dirt off with a soft cloth dampened with cleaning alcohol.
Turn down sound volume. Function can also be restored by turning
power off and on again.(Speaker volume is reduced automatically
when the speaker prote-ction circuit operates).
Write MP3/WMA files onto disc properly.
Use properly encoded MP3/WMA files.
Use ISO9660 level 1,2 or JOLIET or Romeo file system.
Clean the CD with a soft cloth.
Replace with a CD without scratches.
Use properly encoded MP3/WMA files..
Let dry for about 1 hour with the power on.
Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
This is a failure of CD deck mechanism.Consult your
dealer
Replace with a non-scratched, non-warped disc.
Eject the disc and reload it properly.
-3-
Measure
Measure
CZ109/CZ109A
Reset button