Xerox 6180N - Phaser Color Laser Printer 시작하기 매뉴얼 - 페이지 23

{카테고리_이름} Xerox 6180N - Phaser Color Laser Printer에 대한 시작하기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox 6180N - Phaser Color Laser Printer 34 페이지. Color laser printer
Xerox 6180N - Phaser Color Laser Printer에 대해서도 마찬가지입니다: 설치 매뉴얼 (34 페이지), 사양 시트 (2 페이지), 사용자 설명서 (32 페이지), 사용자 설명서 (28 페이지), 설치 매뉴얼 (2 페이지), 보안 매뉴얼 (38 페이지), 릴리스 노트 (2 페이지), 설치 매뉴얼 (2 페이지), 시작하기 매뉴얼 (37 페이지), 매뉴얼 (34 페이지), 매뉴얼 (34 페이지), 사용자 설명서 (32 페이지), 설치 및 운영 매뉴얼 (8 페이지), 평가자 매뉴얼 (16 페이지), 사양 (4 페이지)

Xerox 6180N - Phaser Color Laser Printer 시작하기 매뉴얼
19
Caveat
Copy-Sensitive CME jobs print with extra
pages.
Avoidance: Program a Copy-Sensitive CME in
the START JDL, even if it is a CME
CONSTANT to print a space. The output
prints correctly.
Long jobs that are simplex with a solid
highlight color image in the same location on
each page may cause staining on the fuser
that appears on subsequent jobs. Contact the
Xerox customer support center for assistance.
Jobs programmed with front covers do not
print.
Avoid programming front covers at this time.
Programming a negative shift with JIS B4
stock causes a misalignment between the
black and highlight color images.
Use of DHCP is not recommended. Assign a
static IP address for the system.
DocuSP Remote Workflow does not run in the
Solaris operating system. Use Remote
Workflow on a Windows platform only.
Mismatch processing for highlight color
printing is not supported for IPDS. When
performing highlight color printing, the IPDS
decomposer always prints in the loaded color.
In addition, transparent highlight color mode is
not supported.
Restarting DocuSP causes Remote Services
to restart. Do not restart DocuSP while
capturing or transferring data.
A C17-350 fault occurs when the system
attempts to backup the billing meter
information when the printer is switched off.
Switch on the printer and restart the DocuSP
software to clear the error.
The DocuSP 4.x UI functions much slower on
an Sun Ultra 2.
In Printers, Stackers, if a selection is made for
All Stackers, the selection is not modified for
all. Select each stacker individually and make
the necessary change.
The Reposition Output display only shows the
end of the job and does not show the end of
the set.
Applicable printer product
All monochrome printers
DocuTech 180/155/128 HLC
DocuTech 180/155/128 HLC
DocuTech 180/155/128 HLC
DocuTech 180/155/128 HLC
DocuTech 180/155/128 HLC
DocuTech 180/155/128 HLC
DocuTech 180/155/128 HLC
DocuTech 61xx
DocuTech 61xx
DocuPrint 1xx EPS
DocuPrint 1xx EPS