Xerox 850DP - Phaser Color Solid Ink Printer 릴리스 노트 - 페이지 23

{카테고리_이름} Xerox 850DP - Phaser Color Solid Ink Printer에 대한 릴리스 노트을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox 850DP - Phaser Color Solid Ink Printer 33 페이지. Installation guide for accxes 10.2
Xerox 850DP - Phaser Color Solid Ink Printer에 대해서도 마찬가지입니다: 사양 (2 페이지), 운영자 매뉴얼 (16 페이지), 보충 설명서 (1 페이지), 보충 설명서 (11 페이지), 설정 매뉴얼 (1 페이지), 청소 지침 매뉴얼 (9 페이지), 업그레이드 매뉴얼 (8 페이지), 보충 설명서 (26 페이지), 릴리스 노트 (11 페이지), 릴리스 노트 (11 페이지), 설치 지침 (2 페이지)

Xerox 850DP - Phaser Color Solid Ink Printer 릴리스 노트

8.5.5 Large Scaling Factors

Images set to scale beyond the largest installed roll will not scale beyond the largest width unless
a specific roll is selected, a specific page size is selected, or mismatch mode is set to something
other than scaling. This is a behavior that has changed from previous releases (prior to 9.0).
For example: The largest roll installed is 36". Scaling is set to 999%. Submit an ARCH E sized
drawing (Media Size = Any, Mismatch = Scaling). The drawing will not be scaled.
In order for the output to exhibit the desired scaling factor, one of the following conditions must be
met:
What to do:
Set Mismatch Mode to Substitute
Request a Media Size of ARCH E via WebPMT, ACT, or the Driver
Request a Media Size 36" Roll via WebPMT, ACT, or the Driver

8.5.6 Pen Palettes

For Internet Explorer version 5.00.3105.0106, when you try to save a pen palette it opens
instead; you might have to manually copy and paste the pen palette information into a file. (To
locate your Internet Explorer version number, select Help > About in your browser toolbar.)"
8.5.7 HPGL Page – End of File
If the files are streamed via any port on the system, these are treated as a single job and no reset
is done between them. However, if one uses the LPD protocol to send the files one at a time, the
effect is that the printer is reset after each job. If the "Reinitialize after EOF" is set to be on, the
AccXES firmware will reset the printing parameters after each plot file that is received by a serial
port or a parallel port. To reset the HPGL parameters on the WebPMT, select Printer Defaults >
Emulations > HPGL. Click on the box in front of "Reinitialize after EOF". Click on the "UPDATE
PRINTER" button.

8.5.8 Display of Media Usage

The WebPMT Linear Media Usage displays the Media Usage in METERS. The mechanical
meters used on the Xerox Wide Format Print System 721p IOTs can be programmed using the
IOT diagnostics and are determined by which mode (ANSI or ISO) that the IOT is programmed to
operate in. The units of measurement may not be the same.
Both the WebPMT and Test print display Linear Media Usage as zero (0) for the 6030 and 6050
printers. This is caused by a limitation in the interface between the AccXES controller and the
printer. The linear media information is available from the web page of the printer itself on the
status screen.

8.5.9 Saved Parameter Settings

When changing an Active User Setup Parameter and then pressing the "UPDATE PRINTER"
button, all the settings on the Miscellaneous Page become part of that Active User parameter set.
(On the WebPMT, go to Printer Defaults > Printer Setup > Miscellaneous > Active User Setup
Field.) A user can change parameters on this Miscellaneous page, put in a number into the
Active User Setup parameter field, and then select the "UPDATE PRINTER" button to save the
changes. When that same number is put into the Active User Setup field later, the same
parameters should appear. However, at the present time the selections on the Miscellaneous
Page transfer to other Active User numbers also. For example, if you put in an Active User Setup
Page 23