Xerox DocuColor 40 설정 매뉴얼 - 페이지 2

{카테고리_이름} Xerox DocuColor 40에 대한 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox DocuColor 40 4 페이지. High speed paper-backed transparencies
Xerox DocuColor 40에 대해서도 마찬가지입니다: 매뉴얼 사용 (12 페이지), 참조 매뉴얼 (13 페이지), 설정 매뉴얼 (8 페이지), 보충 설명서 (17 페이지), 사용 지침 (1 페이지)

페이지 인쇄

Fiery X40 with version 1.0 Software, Digital Front End for DocuColor 40/30

Environmental Requirements

Operating Temperature

Humidity (non condensing)

Altitude (above sea level)

Server Specifications (minimum)

433 MHz Celeron Processor

256 MB RAM

CDROM

Mousitometer

ZIP Drive

8.4 GB IDE hard drive

10/100 BaseT Network capability (auto sensing)

Y2K compliant.

Note:

Only 4GB out of 8.4 GB is used for printing and file storage.

Network Connectivity

Protocol Stack

Printing

Services

Novell IPX / SPX

PServer

Ethernet 802.2

Ethernet 802.3

Ethernet_II

Ethernet SNAP

Token Ring 802.2

(option)

Token Ring SNAP

(option)

TCP / IP

LPD/LPR

Ethernet_II

Token Ring SNAP

(option)

TCP / IP

SMB

Ethernet_II

Token Ring SNAP

(option)

TCP / IP

HTTP/IPP

Ethernet_II

TCP / IP

SPM/Port

Ethernet_II

9100

AppleTalk

PAP

Ethernet SNAP

(EtherTalk Phase 2

only)

Parallel Port

LPT1

N/A

The customer is responsible for supplying one network drop to enable the install.

Printing Specifications

PostScript

The Fiery X40 is a true Adobe PostScript 3 controller with PDF

native printing.

Print Speed / System Performance

The maximum print speed for the X40 system is limited by the

print speed of the DocuColor 30/40.

DocuColor 30/40 is a document printer; therefore in reverse

order printing the print engine will not cycle up until the entire job

is ready. This will impact First Copy Out Time (FCOT). The

copier may cycle down between each job depending on job

complexity.

Overall system performance ('Click to Clunk' time) is primarily

dependent upon the software applications and network

Terms and product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.

Customer Expectation Setting Document

Min.

Max.

F (10

104

F (40

5% RH

95% RH

10,000 ft.

(3,048 m)

Supported Frame

Platform

Types

Windows NT

4.0

Windows 95, 98

Windows 2000

Windows NT

4.0

Windows 95, 98

Windows 2000

SunOS 4.1.x

Windows NT

4.0

Windows 95, 98

Windows 2000

Windows NT

4.0

Macintosh

Windows NT

4.0

Windows 95,98

Windows 2000

December 1, 2000

environment being used. Rasterizing (RIP-ing) is only a small

fraction of Click to Clunk time.

Printing with custom software applications may produce

unexpected or unknown results.

The X40 DC 30/40 provides accurate billing of all color and

black & white images when programmed in black detection

mode. When black detection is enabled, productivity will be

affected by the detection of the black toner to process color

mix.

Maximum Image Sizes

The maximum image size from an application is limited to the

image size produced by DocuColor 30/40. The application and

the DocuColor 30/40 setup controls image position.

The maximum imageable area for the DocuColor 30/40 is as

follows:

Copier

Mode

Printer

17.13

Mode

IOT Firmware supported

Firmware version 4.6 and higher only. X40 will not

communicate with earlier versions.

ECT Compression

The Compression efficiency is dependent on file type and

complexity. Artifacts may be possible depending on the file

complexity. Compression can not be turned off.

Calibration

Mousitometer is the primary calibration method through

ColorWise Pro Tools.

The Mousitometer is supported with ColorWise Pro Tools/

Command workStation for Windows or with the FACI kit. Mac

is not supported.

For best results, calibrate on media that will be used for the

print job.

An optional X-Rite DTP32 densitometer is also available for

use with ColorWise Pro Tools.

Color monitor calibration is the responsibility of the customer.

Optimal print quality is achieved by using a densitometer. For

RGB emitting applications (PowerPoint, Word, and Excel), use

the DocuColor 30/40 calibration target. For CMYK applications

(Quark, Pagemaker) use the SWOP target.

Print Quality and Color Management

The appearance of the document displayed on the monitor

screen may not match the output print because the monitor

uses RGB color space parameters.

For imported RGB images, optimal color is achieved in the

EPS format. Other imported file formats may produce

unexpected results.

Separations Support

For the PC, only QuarkXPress & PageMaker should be used

for separations.

For the Mac, only QuarkXPress 4.0 or PageMaker version 6.5

can be used for separations.

The Combine Separation option is only supported for

QuarkXPress and PageMaker using four-pass color.

Inches

0.5% X 11.69

0.5%

432

0.5% X 11.69

435

0.5%

Millimeters

0.5% X 297

0.5%

0.5% X 297

0.5%