Xerox Versant 2100 Press 고객 기대치 및 설치 매뉴얼 - 페이지 19

{카테고리_이름} Xerox Versant 2100 Press에 대한 고객 기대치 및 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox Versant 2100 Press 49 페이지. Entry production color presses
Xerox Versant 2100 Press에 대해서도 마찬가지입니다: 보안 매뉴얼 (45 페이지)

페이지 인쇄

Xerox Versant 2100 Press 고객 기대치 및 설치 매뉴얼

1. Electrical Requirements

Detailed Specifications

Finishing Specifications

Offset Catch Tray (OCT)

The Catch Tray holds a maximum of 500 sheets.

Catch Tray

 If utilizing the Catch Tray, overall productivity will decline if offsetting mode is selected. The print engine will pause printing to offset

Limitations

between sets, and then resume. Productivity loss depends on the number of sheets per set, with single-page jobs representing the worst

case (approximately 50% productivity loss)

 Sheets smaller than 6.7 inches (170 mm) in the cross-process direction (e.g. the feed edge) cannot be offset

 Sheets larger than 11.7 inches (297 mm) in the cross-process direction (e.g. the feed edge) cannot be offset

 With the EX/EX-P Fiery Print Server, the Offset Mode box on the Finishing tab must be checked to enable offsetting.

Interface Module

TIP:

The Interface Module is required with any system configuration that has one or more finishing device, except the Offset Catch Tray (OCT).

The Interface Module acts as a paper path from the press to the finishing device; it also allows communication between the press and the finishing device. The

Interface Module also cools and decurls paper as it exits the press and before it enters the finishing device.

GBC AdvancedPunch Pro

The GBC AdvancedPunch Pro is an inline die punch that uses modular die sets to create a variety of hole punch patterns in a range of papers sizes, from A4 or 8.5

x 11 inch (LTR), long-edge-fed to 12x18 or SRA3 media, to support offline binding. The GBC AdvancedPunch Pro is supported by all print servers. The GBC

AdvancedPunch Pro requires an Interface Module as well as a High Capacity Stacker, Standard Finisher, Booklet Maker Finisher, or Standard Finisher Plus (and

additional third-party device).

GBC

 Supports media from 75-300 gsm, (120-300gsm coated)

AdvancedPunch

 Supports tab stocks: letter (3, 4, 5, 8, 10 bank), ½ letter (3 and 5 bank), A4 (5 and 10 bank), and A5 (3 and 5 bank)

Pro Specifications

 The GBC AdvancedPunch Pro is able to bypass all coated and uncoated media sizes and weights that are printed on the Press

 Requires an additional electrical receptacle; refer to the

GBC

 GBC AdvancedPunch Pro does not work in conjunction with C/Z-fold or Standard Finisher punch, staple, or booklet making

AdvancedPunch

 Hole punch position from edge of paper is user adjustable using the AdvancedPunch Pro LCD User Interface

Pro Limitations

 Opening the door of the GBC AdvancedPunch Pro while the machine is running will cause the machine to jam and shut down

 Gloss coated media may not run as reliably as uncoated paper. Typically, coated papers and high area coverage exhibit increased

variability in paper handling due to lower coefficients of friction, resulting in a broader distribution of punch registration and elevated

jam rates

 Stacking may be misaligned on jobs containing tab stock; these jobs will require additional jogging before final finishing

 Due to the nature of punching holes, each punched sheet is slightly deformed, and when stacked, the edge with the holes will have an

increased height compared to the non-punched edge.

Punch Dies

The GBC AdvancedPunch Pro is capable of punching a variety of hole-punch patterns by simply changing the punch die. Punch dies can be

changed in seconds without tools. The punch dies currently available are listed below. Each die set has a 90 day warranty from date of

purchase. Punch dies are ordered using the Supplies ordering process.

Punch die life will be maximized if lightly oiled every 100K punch cycles (approximately every 2 months) with light machine oil such as 3-in-1

Oil. Small deposits of oil will be observed around the perimeter of the punched holes until the excess oil is absorbed (usually within 20 sheets).

Customer Expectation and Installation Guide

Reduced stack quality may be experienced due to variability in the punch hole formation

When sending output to the stack tray of the High Capacity Stacker, if this stack height difference exceeds one inch, the

machine will shut down and alert the operator to unload the stacker tray. This is done to prevent a jam and will result in a

reduction of stack capacity depending on the die being used

Electrical Requirements for Optional Devices

Xerox Confidential

Xerox

Versant™ 2100 Press