Xerox WORKCENTRE 7120 참조 매뉴얼 - 페이지 18

{카테고리_이름} Xerox WORKCENTRE 7120에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox WORKCENTRE 7120 29 페이지. Color networking mfp a3
Xerox WORKCENTRE 7120에 대해서도 마찬가지입니다: 평가자 매뉴얼 (25 페이지), 평가자 매뉴얼 (24 페이지), 참조 매뉴얼 (30 페이지), 사양 (14 페이지), 사양 (14 페이지), 경쟁사 비교 (11 페이지), 경쟁사 비교 (11 페이지), 브로셔 및 사양 (4 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 빠른 사용 설명서 (20 페이지), 참조 매뉴얼 (32 페이지), 시스템 관리자 매뉴얼 (20 페이지)

페이지 인쇄
Xerox WORKCENTRE 7120 참조 매뉴얼
Time (in milliseconds)
Event
o _----r---r----------
Card reader receives valid read order and reader is in "busy automatic" state.
10
20
B
30
40
1----1-----------
Column 1 arrives at read station. Mode change (EBCDIC to binary) will occur at
50
60
70
80
90
100
110
120
130
140
C
this time if rows 1 and 2 are punched.
Column 80 arrives at read station.
End of card is detected; card reader signals "channel end
ll
to controlling system.
Card reader returns to
II
ready'. condition (a new
510
can be accepted if no in-
terrupt is pending) unless the controlling system specifies command chaining, in
which case the reader requests a new read order.
150~~-------------
Card advances from read station to stacker station.
New feed cycle begins at
this time if new valid order is present and reader is still in the lIautomatic
ll
mode.
160+--It-------------
Card is stacked in preselected stacker or in error stacker (alternate
2).
Notes
®
If the feed cycle begins while the previous card is being stacked, a stacker transport jam occurring in this time
interval causes the reader to stop the transport motor, switch to IInot operational II, light the FAULT indicator,
and signal lIunusual end
ll
to the controlling system.
®
Feed cycle (approximately 43 milliseconds).
©
The data bytes are transmitted, with respect to the column read time (approximately 1.34 milliseconds), as follows:
Column read pu Ises
EBCDIC mode:
Binary mode:
odd column even column
odd column
transmit one byte
for each column
Transmit rows 12-S
J
Save rows 6-9
l
Transmit rows 2-9
Transmit rows
12-1
plus rows
6-9 of previous column
©
If stacker jam occurs after new feed cycle begins, action during this interval is identical to note A. If stacker
jam occurs before new feed cycle begins, reader turns off transport motor, switches to IInot operational
ll
state,
and lights FAULT indicator ("unusual end" is not signaled in this case).
Figure 4. Card Reader Event Times (Model
7120)
12
Programming Considerations