CARD READER STATES
The initial state of the card reader depends on its power
status.
The complete absence of power to the card reader
subsystem (that is, the absence of its prime ac power and
system dc power) effectively removes the card reader from
the controll ing system.
All attempts to access the card
reader result in a response of "no input/output address rec-
ognition" to the I/O instructions. Furthermore, unpredictable
status conditions are supplied if status response is requested
by the I/O instruction. In the absence of ac power, the
presence of system dc power will enable address recognition,
but the card reader assumes a "not operational" state. Like-
wise, failure of power supplies internal to the card reader
causes the card reader to assume a "not operational" state.
OPERATIONAL STATES
The presence of ac and dc power, with no read station faul t
or transport mechanism fault, enables the card reader to as-
sume either of two device conditions ("ready" or "busy")
and either of two modes ("manual" or
lI
au tomatic"). A read
station fault exists if one or more of the photoelectric
channels for sensing punches in the card rows have fai led to
pass the read station test in the previous card read operation.
A transport mechan ism faul t exists if a card jam exists in any
portion of the card transport area.
The exact condition and mode status of the card reader at
any given time is returned to the control I ing system in re-
sponse to such I/O instructions as 510, HIO, and TIO.
Other I/O instructions, such as AIO and TDV, provide more
specific indications of the card reader's status (see IIStatus
Response" in Chapter 3). A brief explanation of the possible
conditions and modes of the card reader follows.
CONDITIONS
Ready. In the
II
ready
II
condition the card reader is capable
of accepting an SIO instruction, providing no device inter-
rupt is pending. In order to be in the "ready" condition,
the card reader must be operational (that is, all conditions
defined under "Operational States" must be satisfied) and
the execution of an order to read a card is not in progress
or pending.
Busy. In this condition the card reader has accepted an SIO
instruction. The unit will not accept a new SIO until the
current order I ist is completed and no device interrupt is
. pending.
MODES
Manual. The card reader assumes the "manual" mode when
any condition arises requiring operator intervention before
the reader can function normally (e. g., stacker full, hop-
per empty, etc.).
The "manual" mode is forced by the
operator pressing the STOP switch or RESET switch on
the card reader control panel.
The reader can accept an
.
SIO instruction in this mode, but will not act on it in any
way until it enters the "automatic" mode.
Automatic. When all necessary conditions for successful
card reader operation are present, the reader is placed in
the "automatic" mode by the operator pressing the START
switch on the card reader control panel (thus illuminating
the switch).
TRANSITION BETWEEN STATES
The allowable card reader state transitions and the condi-
tions causing the reader to change from one state to another
are summarized in Table 2.
DATA TRANSFER
A card read operation is initiated by the controll ing system
with a START IN PUT/OUTPUT (510) instruction if all the
following conditions are satisfied:
1.
Input/output address recognition exists.
2.
The card reader is in the
1\
ready" condition.
3.
No interrupt is pending.
If the card reader is in the "automatic II mode, it then requests
an order from the control I ing system. After accepting a read
order, the card reader advances a card from the input hop-
per to the read station, and commences to read the card,
column by col umn, beginning with column 1. If reading is
performed in the EBCDIC mode, one 8-bit byte is transmitted
to the control I ing system for each col umn read, and a code
validity check is performed on each byte.
In the binary
read mode three 8-bit bytes are transmitted to the control
I
ing
system for each odd-even-numbered pair of col umns (no
val idity check is performed in this mode). Reading continues
until one of the following conditions occurs:
1.
The end of the card is detected.
2.
The card reader receives a
II
count done" or "halt" sig-
nal from the controlling system.
3.
A "fault" condition is encountered.
If the card read operation was not terminated by a card jam,
the card is then routed to the stacker station, where it is
sensed and directed to the normal stacker unless:
1.
The Read Automatic order specified error stacking and
the validity check (for EBCDIC mode only) indicated
that the card contained an invalid EBCDIC punch con-
figuration, in which case the card is directed to al ter-
nate stacker 2 (Model
7120)
or to the alternate stacker
(Model
7140).
2.
The Read orderspecified error stacking and a data over-
fUn has occurred, in which case the card is directed to
al ternate stacker 2 (Model
7120)
or the alternate stacker
(Model
7140)
and the control
I
ing system is notified of
the error with the Data Overrun and Unusual End
indicators •
Card Reader States/Data Transfer
3
페이지 인쇄