Xerox WorkCentre M118i 빠른 설정 매뉴얼 - 페이지 3

{카테고리_이름} Xerox WorkCentre M118i에 대한 빠른 설정 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox WorkCentre M118i 5 페이지. Copy/print/fax/email
Xerox WorkCentre M118i에 대해서도 마찬가지입니다: 사용자 설명서 (2 페이지), 모듈 매뉴얼 (2 페이지), 빠른 설치 카드 (2 페이지), 소프트웨어 설명서 (47 페이지), 빠른 설정 매뉴얼 (5 페이지), 매뉴얼 (28 페이지), 스탠드 설치 매뉴얼 (4 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (1 페이지), 설치 매뉴얼 (1 페이지), 시작하기 매뉴얼 (25 페이지), 평가자 매뉴얼 (12 페이지), 서비스 매뉴얼 (12 페이지)

페이지 인쇄
Xerox WorkCentre M118i 빠른 설정 매뉴얼
Enabling Scan to E-mail
To enable the Scan to E-mail feature:
1.
On the control panel, press the Log In/Out button.
2.
Press the Select button below the display to select
a.
Use the numeric keypad to enter the Password. The default password is 11111.
b.
Press the Select button to select Confirm.
3.
Select
Print
Settings, and then press the Enter button.
4.
Press the Select button until you see
5.
Use the numeric keypad to enter the Software Option password for Scan to E-mail, and then press the
Enter button. The password can be found on the inside cover of the Scan to E-mail Instructions.

Configuring Scan to E-mail

After Scan to E-mail is enabled, follow these steps to configure Scan to E-mail on your network.
Set the Administrator E-mail Address
1.
At your computer, launch your web browser.
2.
Enter the machine's IP address in the browser's Address field (http://xxx.xxx.xxx.xxx).
3.
Click the Properties tab.
4.
Select Machine Details on the left sidebar.
a.
Enter the machine's email address in the Administrator E-mail Address field. If an email address for
the machine has not been created, enter your email address. Once an email address is available for the
M118i machine, repeat Steps 1 through 5 in this procedure to replace your e-mail address with the
machine's email address.
b.
Click the Apply New Settings button at the bottom of the page.
c.
Enter the CentreWare IS administrator's User Name and Password, and then click the OK button.
Note
The default CentreWare IS administrator's User Name is admin and Password is x-admin. These
should be changed after network setup is complete.
d.
At the reboot prompt, click the Reboot button.
5.
Wait one minute for the reboot to complete, and then click the browser Refresh button.
System
Settings.
Software Option
on the display, and then press the Enter button.
Xerox WorkCentre M118i
3
Enabling Scan to E-mail