Xerox ColorQube 9202 안전한 설치 및 운영 - 페이지 9

{카테고리_이름} Xerox ColorQube 9202에 대한 안전한 설치 및 운영을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox ColorQube 9202 12 페이지. Mfp
Xerox ColorQube 9202에 대해서도 마찬가지입니다: 설치 및 작동 지침 (14 페이지), 평가자 매뉴얼 (28 페이지), 빠른 사용 설명서 (38 페이지), 빠른 매뉴얼 (8 페이지), 빠른 매뉴얼 (16 페이지), 안전한 설치 및 운영 (12 페이지), 사본을 만드는 방법 (9 페이지)

페이지 인쇄

15. Users should be aware that correct remote repository document pathnames for the receipt of workflow scanning jobs should

start with one '\' as opposed to the two '\'s shown in the SAG (e.g., page 10-15).

16. Xerox recommends that users undergo appropriate training on how to use the device in a secure manner before being assigned

user accounts to access the device.

17. The following windows are available from the Local User Interface with System Administrator login and authentication. These

windows provide standard system configuration or job management capability:

PagePack Passcode - Allows the System Administrator to enter a 4 digit "PagePack PIN" to enable a PagePack device to

•

work with metered supplies. Is accessible by selecting the following screens/buttons in order: [Machine Status] hard button

[Tools] button

accesses the PagePack Passcode screen and enters a valid PagePack PIN, the System Administrator can print out PagePack

courtesy prints by selecting the [Skip] button; however, if the number of PagePack courtesy prints requested exceeds the

allowable limit an appropriate error message will be displayed on the screen and the System Administrator will have to re-

enter a valid PagePack PIN.

Enter Cleaning Unit Passcode - Allows the System Administrator to enter a 4 digit passcode to temporarily extend a

•

Customer Replaceable Unit (CRU) when that CRU has reached its end of life. Is accessible by selecting the following

screens/buttons in order: [Machine Status] hard button

Unit Passcode] button.

Low Supply Warning - Allows the System Administrator to set when to receive low supply warnings for the ColorQube Ink

•

Sticks, Cleaning Unit, and Document Feed Roll. Is accessible by selecting the following screens/buttons in order: [Machine

Status] hard button

button.

Service Plan - Allows the System Administrator to set or change the Service Plan for the device. Is accessible by selecting the

•

following screens/buttons in order: [Machine Status] hard button

Plan] button.

Network Logs – Allows the System Administrator to download network logs to a USB drive for troubleshooting purposes. Is

•

accessible by selecting the following screens/buttons in order: [Machine Status] hard button

Settings] button

a basic or an enhanced level of network log information, and a separate screen will provide information on the completion

status of the download.

Downloaded network logs are always encrypted and require Xerox personnel to decrypt the logs before they can be read by

the System Administrator or other authorized persons.

USB Settings – Allows the System Administrator to enable/disable and set the configuration of the USB Printer Port

•

connectivity. Is accessible by selecting the following screens/buttons in order: [Machine Status] hard button

button

[Network Settings] button

Supply Counter Reset – Allows the System Administrator to manually reset the supply counter for a CRU on the device back

•

to 100% when that CRU is replaced. Is accessible by selecting the following screens/buttons in order: [Machine Status]

hard button

[Tools] button

18. The following windows are available to any authenticated and authorized user from the Local User Interface. These windows

provide standard machine services or job management capability:

Embedded Fax Batch Send Confirmation – Allows a user to either send an Embedded Fax job to a remote destination

•

immediately or include the job as part of a "batch" of Embedded Fax jobs sent to the same destination. Is accessible by

selecting the following screens/buttons in order: [Services Home] hard button

button when a user is submitting an Embedded Fax Send job to the same destination as a previously submitted "delayed

send" Embedded Fax job.

Workflow Scanning Authentication Required – Allows a user to enter the proper user credentials for a workflow scanning

•

job being sent to a network destination that requires user login. Is accessible by selecting the following screens/buttons in

order: [Services Home] hard button

workflow scanning job to a network destination that requires user login

Pausing an active job being processed by the device – Allows the user to pause an active copy, print, workflow scanning,

•

scan to email, Internet Fax or Embedded Fax job while it is being processed. Is accessible by selecting the [Stop] machine

hard button while a job is being processed by the device. Depending on the type of jobs being processed by the device when

the [Stop] button is selected, one of the following Pause windows will be displayed as appropriate to allow the user to

determine whether to delete or continue processing of the job: Scanning Pause window, Printing Pause window, Copy Only

(Scanning and Printing) Pause window, Scanning/Printing (Simultaneous Jobs) Pause window, Scanning Build Job

[Device Settings] button

[Tools] button

[User Interface Settings] button

[Advanced Settings] button

[Troubleshooting] button

[Workflow Scanning] button

[Enter PagePack Passcode] button. Once the System Administrator

[Tools] button

[Network Logs] button. The System Administrator can download either

[USB Settings] button.

[Resets] button

[Start] hard button when a user is submitting a

[OK] button.

[Device Settings] button

[General] button

[Low Supply Warning]

[Service Settings] button

[Tools] button

[Supply Counter Reset] button.

[Fax] feature button

[Enter Cleaning

[Service

[Network

[Tools]

[Start] hard