Xerox WORKCENTRE 5775 안전한 설치 및 운영 - 페이지 6

{카테고리_이름} Xerox WORKCENTRE 5775에 대한 안전한 설치 및 운영을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox WORKCENTRE 5775 11 페이지. Smart card
Xerox WORKCENTRE 5775에 대해서도 마찬가지입니다: 정보 매뉴얼 (50 페이지), 평가자 매뉴얼 (24 페이지), 데이터시트 (18 페이지), 정보 시트 (8 페이지), 시작하기 매뉴얼 (32 페이지), 사용자 지침 (5 페이지), 사용자 설명서 (8 페이지), 사본을 만드는 방법 (10 페이지), 설치 매뉴얼 (43 페이지)

페이지 인쇄

Use the default values for IPSec parameters listed in the IPSec discussion starting on page 183 in the SAG whenever

possible for secure IPSec setup.

x). To enable the session inactivity timers (termination of an inactive session) from the Web UI follow the instructions on page

194 of the SAG.

y). There is a software verification test feature that checks the integrity of the executable code by comparing a calculated hash

value against a pre-stored value to ensure the value has not changed. To initiate this feature perform the following from the

Web UI:

•

Select the Properties tab.

•

Select the following entries from the Properties 'Content menu': Security

•

Select the [Start] button to initiate the software verification test.

z). To enable the Scan to Mailbox feature from the Web UI:

•

Select the Properties tab.

•

Select the following entries from the Properties 'Content menu': Services

•

Select the [Enable Scan to Mailbox] button and then select the [On Scan tab, view Mailboxes by default] button.

•

Select the [Apply] button. This will save the indicated settings.

For the purposes of the evaluation, the Scan to Mailbox feature was set to store scanned documents only in private folders.

To set the scan policies for the Scan to Mailbox feature, select the following entries from the Properties 'Content menu':

Services

Scan to Mailbox

policies should therefore be set as follows:

•

Deselect [Allow Scanning to Default Public Folder].

•

Deselect [Require per Job password to public folders].

•

Select [Allow additional folders to be created]

•

Select [Require password when creating additional folders].

•

Select [Prompt for password when scanning to private folder].

•

Deselect [Allow access to job log data].

Passcodes for Scan-to-Mailbox mailboxes should be selected to be as random as possible and should be changed on a

regular basis, consistent with applicable internal policies and procedures. Xerox recommends that the minimum length of a

password assigned to a private Scan to Mailbox folder be 8 alphanumeric characters.

aa). In the evaluated configuration Embedded Fax Secure Receive option should be enabled,

should be enabled, and both the Local Polling option and embedded fax mailboxes should not used.

After normal business hours Fax Forwarding on Receive should be enabled and secure receive should be disabled.

•

To enable/disable Secure Receive from the Local UI follow the instructions under "Secure Receive" on page 279 of the

SAG. The System Administrator should ensure that the secure receive passcode, which is fixed at 4-digits, is changed

every three days.

•

To enable Fax Forwarding on Receive and establish up to five fax forward rules from the WebUI follow the instructions

for "Fax Forward" starting on page 284 of the SAG.

The Mailbox and Polling Policy should be set to delete received faxes when they are printed. To set the Mailbox and Polling

Policy follow the instructions under "File Management – Retained Document Policy" on page 282 of the SAG. Makes sure

the 'Delete on Print' option is selected.

bb). For best security print jobs submitted to the device from a client or from the Web UI should be submitted as a secure print

job. Once a secure print job has been submitted the authenticated user can release the job for printing at the Local UI

following the directions for releasing a job on page 244 of the User Guide.

cc). In the evaluated configuration the Secure Print security function should be set to require the user ID for identification

purposes to release a secure print job. Follow the instructions on page 31 of the SAG to access and configure the Secure

Print security function.

dd). Before upgrading software on the device via the Manual/Automatic Customer Software Upgrade, please check for the latest

certified software versions. Otherwise, the machine may not remain in its evaluated configuration.

ee). In the evaluated configuration, customer software upgrades via the network should be disabled.

This will apply to any received fax, including faxes that are remotely polled to the device from another remote fax machine or remote device.

Scan Policies. Public folders are not allowed in the evaluated configuration. The scan

Software Verification Test.

Scan to Mailbox

Enablement

fax forwarding on receive feature