ALDEN Satlight Track 60 설치 및 사용자 설명서 - 페이지 6

{카테고리_이름} ALDEN Satlight Track 60에 대한 설치 및 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. ALDEN Satlight Track 60 15 페이지. Portable satellite antenna

Satlight Track60 - Quick Setup and User Guide
1. Connect and Setup the Satlight Track60 as illustrated by the Diagram Below. The Satlight track60 is a portable auto dish, in which it's base "dish unit"
can be mounted /installed on a vehicle or be temporarily placed on a flat surface or be held down on a grass area with the tent pegs supplied.
2. On the SSC HD Unit (Control unit / black box) press the "Power On" button.
3. By default OptusD3 (For VAST and PayTV) will be seen flashing on the SSC LCD screen and no other press of a button is required . If "OptusD3" is Not
flashing , Keep Pressing the UP Button once at a time and Stop when you see "OptusD3" flashing on the LCD. The Dish will deploy Up and start searching,
when "OptusD3 is found the LCD will display "Pointing OK"and the green LED will be on.
4. When finished Usage, Press the "Off" button to fold the Dish Down ,disconnect cabling and Stow away.
Other relevant Information :
a) 1
time (out of the box) or out of the same location area's (250km radius) satellite searches will result in longer "Pointing Ok" times, approx
st
- 3 mins or so, subsequent same area searches approx- 1 minute.
b) When the Green LED is "On" the unit is in Standby mode and consumes approx- 4 watts power.
c) Other satellites selectable via the "Up" button. Set with 4 satellites and 4 Empty/Not used parameters in memory
d) Skew (lnb rotation for current position) is automatically achieved via the units GPS, auto Skew Set function.
e) The LNB (twin Output) value used is 10700 *Make sure your satellite receivers lnb value is set to 10700
f) Every satellite is programmed with 3 transponder frequency settings in memory. The extra's are used as backups
g) The OptusD3 satellite selection / parameter is the strongest and best to use with VAST and PayTV services.
h) If the OptusD3 selection in an area has persistent weak signal, try using the Optus C1 selection instead.
i) The satellite parameters are modifiable manually from the SSC units "Menu System" or by upgrading them via it's USB port.
*Simple and Quick Satellite parameters and firmware Upgrade via the usb port !
ALDEN SSC (Front View)
Sat. OPTUS D3
ON/OFF
Up Down Menu-Select
Zone de recherche
Rotation
360°
Poser l'antenne sur une surface plane, stable, ou directement sur le sol.
La tête LNB doit être obligatoirement dirigé vers le sud.
Aucun obstacle doit etre
Motor cable
Coax cable
LNB IN
OUT TO
RC
14/18V 300mA
DEMO
Coax cable
Satellite/Vast Receiver (Rear view)
IR
S/PDIF
VIDEO
L
R
OUT
IN
USB
AUDIO
HDMI
HDMI Cable
6
Designation
w
s
Green Led
ALDEN SSC (Rear View)
MOTOR SKEW
DATA
+ after ignition
(1,5A. min.)
ON
OFF
DC12V/5A
TV
Function
Switch the module on/off.
Select the satellite/navigate
in the menu.
Close the dish/navigate
in the menu.
Access to the setting menu.
SKEW option management.
On: The S.S.C. is in stand by mode
Off: The S.S.C. is off
(Power intake = 0 Amps)
10 - 15VDC
TV OUT
Note : Regarding the "+ after ignition" connection
*If the Dish is to be Permanently Installed on a RV Vehicle as a Safety
measure it is highly recommended this feature be utilized as the dish
Automatically folds down when the vehicles ignition key is turned on.
* Supplied with a «Male end»
cigarette lighter plug with a
internal 5Amp fuse
*Optional Not supplied
«Female end» cigarette lighter Socket
with Alligator Clip