Xerox 850DP - Phaser Color Solid Ink Printer 설치 지침

{카테고리_이름} Xerox 850DP - Phaser Color Solid Ink Printer에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox 850DP - Phaser Color Solid Ink Printer 2 페이지. Installation guide for accxes 10.2
Xerox 850DP - Phaser Color Solid Ink Printer에 대해서도 마찬가지입니다: 사양 (2 페이지), 운영자 매뉴얼 (16 페이지), 보충 설명서 (1 페이지), 보충 설명서 (11 페이지), 설정 매뉴얼 (1 페이지), 청소 지침 매뉴얼 (9 페이지), 업그레이드 매뉴얼 (8 페이지), 보충 설명서 (26 페이지), 릴리스 노트 (33 페이지), 릴리스 노트 (11 페이지), 릴리스 노트 (11 페이지)

Xerox 850DP - Phaser Color Solid Ink Printer 설치 지침
AccXES Version 10.2 Installation Instructions
Warning: If you have an HFT controller with AccXES 8.0 or 8.5, upgrading to AccXES 9.0 will
cause you to lose the following Data Format Interpreters (DFI):
• VCGL
• Versatec Raster (VRF & VDS)
• CGM
These DFIs are no longer part of the standard system. A feature key is necessary to enable them.
The DFI Feature Keys can be purchased through Xerox Sales or an Authorized Reseller. See Step
1 to determine if you have the appropriate controller.
Note: For the Xerox 6050 and 6030 Wide Format products, one must activate the AccXES print server by
downloading the appropriate print server feature
Warning: If the current AccXES Version is 8.0 or lower, upgrading to AccXES 9.0 will eliminate all existing
feature keys. Once installation is complete, you will need to reinstall your feature keys. If you are currently
at AccXES 9.0 or greater, your feature keys will be retained.
Step 1
Determine your Hardware Configuration
There are distinct versions of firmware for each controller hardware platform. Firmware is available for the
hardware platforms as indicated below. Your hardware platform can be determined by examining the
printer configuration test print or serial number (found on the AccXES controller unit). Note your hardware
version. Note: Use the HFT firmware as this will be the correct downloadable binary for PUN controllers.
Controller
PUN
HFT
CNG
KLF
N5T
EV4
Step 2
Release Notes
Download, print, and read the AccXES release notes (pdf format). The release notes can be found in the
documentation section or by using the 'See Also' link.
Step 3
Check Disk Size and RAM Requirements
Consult the Recommended Configurations Chart in the AccXES Release Notes to confirm that your
Controller has the required disk size and RAM needed for the AccXES upgrade. This chart can be found in
the documentation section or by using the 'See Also' link.
Step 4
Job Accounting Migration (if applicable)
Warning: As a precaution, save your Job Accounting Data prior to upgrading. If you have AccXES 7.5 or
greater and are using Job Accounting, use the Account Management Tool (AMT) to collect existing Job
Based Accounting Data from the AccXES Controller / Printer. If you have AccXES 6.1 or lower and are using
job accounting, please read the Job Accounting Migration document (found in the Documentation section)
which describes the migration process from the legacy accounting system to the new Job Based Accounting
system. Legacy Job Log files are deleted when upgrading to AccXES 7.5 or greater. Use the Web Printer
Manager Tool, Scanner UI or ACT to retrieve/store your legacy data prior to upgrading AccXES.
key.
CPU from Test Print
RTT-MPC 7410
RTT-MPC 7410
PPC740 – 200
PPC740 – 200
PPC740 – 200
MPC8240-250
Serial Number
PUN-XXXXX
HFT-XXXXX
CNG-XXXXX
KLF-XXXXX
N5T-XXXXX
EV4-XXXXX