Xerox M123 WorkCentre 참조 매뉴얼 - 페이지 17

{카테고리_이름} Xerox M123 WorkCentre에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox M123 WorkCentre 20 페이지. Stand installation guide
Xerox M123 WorkCentre에 대해서도 마찬가지입니다: 설치 매뉴얼 (2 페이지), 평가자 매뉴얼 (12 페이지), 브로셔 및 사양 (6 페이지), 설치 매뉴얼 (2 페이지), 네트워크 매뉴얼 (50 페이지), 스캔 매뉴얼 (28 페이지), 빠른 설치 카드 (2 페이지), 매뉴얼 (28 페이지), Office 피니셔 설치 매뉴얼 (6 페이지), Office 피니셔 설치 매뉴얼 (6 페이지), 하드웨어 설치 매뉴얼 (4 페이지), 대용량 트레이 설치 매뉴얼 (3 페이지), 대용량 트레이 설치 매뉴얼 (3 페이지), 하드 드라이브 키트 설치 매뉴얼 (2 페이지), 인버터 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 하드웨어 설치 매뉴얼 (2 페이지), 스탠드 설치 매뉴얼 (2 페이지), 빠른 네트워크 설정 매뉴얼 (7 페이지), 서비스 매뉴얼 (22 페이지)

페이지 인쇄

Example 4 Header for Confidential Print

<ESC>%-12345X@PJL JOB MODE=PRINTER<CR><LF>

@PJL COMMENT Beginning PCL Job<CR><LF>

@PJL SET OUTBIN=MAINTRAY<CR><LF>

@PJL SET QTY=1<CR><LF>

@PJL SET RESOLUTION=600<CR><LF>

@PJL SET HOLD=STORE <CR><LF>

@PJL SET HOLDKEY="1234"<CR><LF>

@PJL SET USERNAME="Nagaoka" <CR><LF>

@PJL SET JOBNAME="Job1" <CR><LF>

@PJL ENTER LANGUAGE=PCLXL<CR><LF>

PCL DATA ..........

PCL Feature Dependencies/Caveats

•

All PJL commands must be in the first 2,500 bytes of the job.

•

To combine printer escape commands (not including PJL commands):

−

•

In case of duplicate commands, the last one requested takes precedence.

•

The @PJL SET COPIES takes precedence over the PCL Escape

Command (<ESC>& | int X>) to set copies. In general, a PJL command

takes precedence over a PCL command.

•

Do not duplex any job with these media sizes: A6, B6. A request to duplex

these media sizes is ignored.

•

Do not staple any job with these media sizes: A6, B6, A5, 5.5 x 8.5. A

request to staple these media sizes is ignored.

•

Do not duplex any job with transparencies, labels, envelopes or tab-stock

The duplex print request is ignored if you use any of these media types.

•

Use one of these methods to specify media selection:

−

WorkCentre M128/M123 Reference Guide

The first two characters after the <esc> MUST be the same.

All alpha characters MUST be lowercase, except the final terminating

character.

Commands are read left to right. Combine commands in the order you

wish them to execute.

For example, combine print 5 copies (<ESC>&|5X) and use letter size

(<ESC>&|2A) as <ESC>&|5x2A.

Describe the media attributes with size and type and allow the device to

select the correct source tray. If you describe the media, leave source

tray information out of the request or set to Auto. Otherwise, the tray

selection defeats the auto tray selection capabilities of the device.

Indicate the media feed tray to use. In doing so, you allow the device to

select media feed trays based on paper type defined by SYSTEM

DEFAULT unless specified otherwise. This method prevents

inadvertent use of special paper types. To override a paper type

definition, include a paper type specification of UNSPECIFIED in the

job.

Page

dc05cc0364