Xerox WorkCentre 4265 안전한 설치 및 운영 - 페이지 7

{카테고리_이름} Xerox WorkCentre 4265에 대한 안전한 설치 및 운영을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox WorkCentre 4265 10 페이지. Monochrome multifunction printer
Xerox WorkCentre 4265에 대해서도 마찬가지입니다: 정보 (4 페이지), 설치 매뉴얼 (2 페이지), 빠른 사용 설명서 (20 페이지), 설치 매뉴얼 (2 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지)

페이지 인쇄

7. SNTP:



If it is desired to use an NTP server to synchronize and set the internal system time used by the device follow the

instructions under "Configure SNTP" in Section 3 of the SAG.

8. Scan to USB:



To enable/disable Scan to USB on the device follow the instructions for "Scan to USB" in Section 7 of the SAG.

9. Print from USB:



To enable printing from USB on the device, follow the instructions for "Enabling Print from USB" in Section 5 of the

SAG.

The following features and protocols are not included in the evaluated configuration:



Reprint from Saved Job



SMart eSolutions



Custom Services (Extensible Interface Platform or EIP)



Network Accounting and Auxiliary Access



Internet Fax



Use of Embedded Fax mailboxes



USB Direct Printing



Web Services



SNMPv3



IPv6



IPsec

Customer software upgrades via the network are not allowed as part of the evaluated configuration. System software

upgrades are disabled by default to prevent unauthorized replacement of the system software. Administrators should only

enable software upgrades when performing an upgrade, and software upgrades disable when complete. Software upgrades

can be enabled/disabled by following the instructions for 'Enabling Upgrades' under 'Updating the Printer Software' in

Section 9 of the SAG.

II.

Secure Acceptance:

Secure acceptance, once device delivery and installation is completed, should be done by:



Printing out a Configuration Report from the Web UI by following the "Printing the Configuration Report" instructions under

"Initial Setup in CentreWare Internet Services" in Section 2 of the SAG.



Comparing the software/firmware version listed on the Configuration Report with the Evaluated Software/Firmware version

listed in Table 2 of the Xerox Multi-Function Device Security Target WorkCentre 4265, latest version issued and make sure

that they are the same.



Following internal customer policies and procedures required to evaluate and install devices in your environment.

III. Secure Operation of Device Services/Functions Part of the Evaluated Configuration

Change the following passcodes on a regular basis, chose passcodes to be as random as possible and set to the indicated

minimum lengths:



Smart Card or CAC passcode – 8 characters (alphanumeric)



Secure Print passcode – 6 digits

In the evaluated configuration the System Administrator should ensure that all pathways and services are 'Not Allowed' or

'Not Allowed & Hidden' for guest users so that they can be accessed only by authenticated users. Follow the instructions in

the "Configuring User Roles" under "User Roles" under "User Permissions" in Section 4 of the SAG to lock all pathways and

services for guest users.

Authentication passwords for unique user accounts established for users should be set to a minimum length of 8

(alphanumeric) characters unless applicable internal procedures the System Administrator must comply with require a

minimum password of a greater length.

Ensure that local usernames established on the device match domain names and that both map to the same individual.

Operation of IIO and ODIO:



Set the 'Confirmation Report' setting to "On" when setting up a manual or scheduled ODIO from the Control Panel or

Web UI so that a Confirmation Report will always be printed upon completion of an ODIO.