Xerox WORKCENTRE C2424 사용 설명서 - 페이지 3

{카테고리_이름} Xerox WORKCENTRE C2424에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox WORKCENTRE C2424 6 페이지. Copier-printer
Xerox WORKCENTRE C2424에 대해서도 마찬가지입니다: 빠른 참조 매뉴얼 (14 페이지), 브로셔 (8 페이지), 보충 설명서 (7 페이지), 사양 (6 페이지), 사용자 설명서 (43 페이지), 시작하기 매뉴얼 (26 페이지), 사용자 설명서 (21 페이지), 사용자 설명서 (20 페이지), 유지 관리 매뉴얼 (20 페이지), 사용자 설명서 (19 페이지), 사용 설명서 (16 페이지), 매뉴얼 (12 페이지), 설치 매뉴얼 (4 페이지), 설치 매뉴얼 (2 페이지), 피드 롤러 키트 교체 (2 페이지), 설정 매뉴얼 (2 페이지), 자발적 제품 접근성 템플릿 (10 페이지), 경쟁사 비교 (3 페이지), 빠른 참조 매뉴얼 (14 페이지), 서비스 매뉴얼 (11 페이지), 빠른 참조 매뉴얼 (13 페이지)

페이지 인쇄

Follow all warnings and instructions marked on, or supplied with, the system, options and

■

supplies.

Caution

Use of other than Genuine Xerox WorkCentre C2424 Solid Ink may affect print and copy

quality and system reliability. It is the only ink designed and manufactured under strict

quality controls by Xerox for specific use with this system. The Xerox Warranty, Service

Agreements, and Total Satisfaction Guarantee do not cover damage, malfunction, or

degradation of performance caused by use of non-Xerox supplies or consumables, or the

use of Xerox supplies not specified for this system.

Note

The Total Satisfaction Guarantee is available in the United States and Canada.

Coverage may vary outside these areas; please contact your local representative for

details.

System Location

■

Place the system in a dust-free area within a temperature range of 50 degrees F to

90 degrees F (10 degrees C to 32 degrees C) and a relative humidity range of 10 percent to

80 percent.

Place the system in an area where there is adequate space for ventilation, operation, and

■

servicing. The recommended minimal spacing is:

■

30 cm (11.8 in.) above, measuring from the top of the document feeder

■

24 cm (9.5 in.) behind

■

10 cm (3.9 in.) on the left side of the system

■

37 cm (14.6 in.) on the right side of the system, to allow access to the maintenance

unit and waste tray.

Do not block or cover the slots and openings on the system. The system may overheat

■

without adequate ventilation.

■

For optimum performance, use the system at elevations below 2,438 m (8,000 ft.).

■

Do not place the system on a carpeted location such as a carpeted floor. Airborne carpet

fibers can be pulled into the system and cause print- and copy-quality problems.

■

Do not place the system near a heat source.

■

Do not place the system in direct sunlight.

■

Do not place the system in line with the cold air flow from an air conditioning system.

■

Place the system on a level, solid non-vibrating surface with adequate strength for the

weight of the system. It should be within 2 degrees of horizontal with all four feet in solid

contact with the surface. The base system weight without any packaging materials is

approximately 42 kg (93 lbs.).

WorkCentre® C2424 Copier-Printer

A-3