Xerox Nuvera 100 참조 매뉴얼

{카테고리_이름} Xerox Nuvera 100에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox Nuvera 100 2 페이지. Production system
Xerox Nuvera 100에 대해서도 마찬가지입니다: 사양 시트 (2 페이지), 기능 설명서 (34 페이지), 계획 매뉴얼 (22 페이지), 사용자 설명서 (40 페이지), 운영 매뉴얼 (34 페이지), 계획 매뉴얼 (20 페이지), 참조 매뉴얼 (42 페이지), 빠른 참조 (2 페이지), 설치 매뉴얼 (2 페이지), 보충 설명서 (48 페이지), 계획 매뉴얼 (38 페이지), 계획 매뉴얼 (16 페이지), 참조 매뉴얼 (2 페이지), 사양 (2 페이지), 힌트 및 팁 매뉴얼 (18 페이지), 힌트 및 팁 매뉴얼 (18 페이지), 시작하기 매뉴얼 (26 페이지), 시작하기 매뉴얼 (30 페이지)

Xerox Nuvera 100 참조 매뉴얼

Duty cycle

Targeted impressions per month on the Xerox
DocuPrint 100/115/135/155/180 EPS:
Printing system
Minimum
Maximum
DP100
800 thousand
3 million
DP115
1 million
3.5 million
DP135
1.2 million
4 million
DP155
1.4 million
4.5 million
DP180
1.8 million
6 million
Note: Usage outside these ranges may vary the
service frequency.
Performance
Reliability performance of the Xerox DocuPrint 100/
115/135/155/180 EPS for the targeted impressions per
month:
Average
Average
Average
Average
Average
Average
service
service
service
service
service
monthly
calls per
calls per
calls per
calls per
calls per
print
month
month
month
month
volume
DP100
DP115
DP135
DP155
1
2.7
2.6
2.5
2.6
million
2
5.4
5.2
5.0
5.2
million
3
8.1
7.8
7.5
7.8
million
4
--
--
10.0
10.4
million
5
--
--
--
--
million
6
--
--
--
--
million
Note: Variables other than monthly print volume affect
the average number of service calls. Please contact
your local Xerox representative for more information.
Resolution
DP 155 and 180: 600 by 2400 dots per inch (dpi)
DP 100, 115, and 135: 600 by 600 dots per inch (dpi)
Speed
The speed at which data can be printed on the Xerox
DocuPrint 100/115/135/155/180 EPS:
Pages per minute
Printing system
(standard)
DP100
100
DP115
115
DP135
135
DP155
155
DP180
180
Note: Throughput rates can vary depending upon job
complexity and system configuration.
* Requires optional 7 by 10 inch enablement kit.
Paper handling
Paper weights: 16 lbs. / 65 gsm bond to 110 lbs. /
200 gsm index cut-sheet weights
Paper sizes:
month
DP180
8 x 10 in. / 203 x 254 mm to
14.33 x 17 in. / 364 by 432 mm, including A4 and A3
2.4
7 x 10 in. / 178 x 254 mm with optional 7 x 10 in.
enablement kit
4.8
Input
Main tray (Tray 1): 1100 sheet capacity of 20 lbs. /
7.2
80 gsm bond paper
Auxiliary tray (Tray 2): 600 sheet capacity of 20
9.6
lbs. / 80 gsm bond paper
The Xerox DocuPrint 100/115/135/155/180 EPS may
12
have up to six input trays: two processor trays and two,
three, or four high-capacity feeder trays.
Output
14.4
Output bin: Each output bin has a capacity of 2500
sheets of 20 lbs. / 80 gsm bond with offset
capability.
Two output bins are standard, with up to two
additional bins available as options.
Sample tray: 100 sheets of 20 lbs. / 80 gsm bond
Refer to Helpful Facts About Paper to help in selection
of preprinted forms, perforated stock and labels.
Controller components
Processor (system unit):
One or two UltraSPARC central processing unit
(CPU) modules
Pages per minute
(using 7 x 10 in. /
1 or 2 GB of memory (one or two 1-GB Dual In-line
178 x 254 mm
paper) *
Memory Modules, or DIMMs)
36 or 73 GB hard disk drive
100
High-density, read-only DVD-ROM drive
115
Diskette drive: uses 3.5 inch, 1.44 MB, double-sided,
154
high-density diskettes
Ethernet
155
1 or 2 Printer Controller Interface (PCI) boards
206
PGx64 or XVR-100 video graphics board
Universal Serial Bus (USB) keyboard and mouse
17-inch flat panel monitor
Note: This configuration may change due to the Xerox
policy of staying up to date with current technology.
Supported client workstations
Xerox DP 100/115/135/155/180 EPS supports the
following types of networked client workstations and
operating systems:
Sun Workstation running Solaris 2.3 or higher
PC running MS-DOS 5.0 or higher, using Ethernet
with TCP/IP or Novell NetWare, and Windows 95/
98, NT, Millennium, 2000, or XP
PC running MS-DOS 5.0 or higher, with one or more
of the following TCP/IP packages:
PC/TCP Network Software by FTP Software, Inc.
Pathway Access by Wollongong Group, Inc.
PC-NFS by Sun Select
Apple Macintosh, System 7 or higher, using
AppleTalk through EtherTalk
Any system that supports RFC-1179 lpr/lpd
PDL compatibility
The system interprets the following data formats:
PostScript levels 2 and 3
PCL5e and PCL6
LCDS
ASCII
PDF
TIFF
VIPP
IPDS (currently not available)
Interface requirements
One or more of the following network communications
systems may be used to transport documents from a
client or host to the printing system.
Ethernet LAN running TCP/IP, AppleTalk, or Novell
NetWare network protocol software
Online – Bus and tag supporting IBM 3211/4245
interface*
Token ring LAN running TCP/IP, Novell 3.x, or
AppleTalk network protocol software*
* Requires additional equipment.
Installation considerations
Data cable: The controller can be separated up to
the length of the data interface cables that connects
them.
20 foot / 6.1 meters, or
Optional 50 foot / 15.2 meters
Power cable lengths are as follows:
Controller:
8 feet / 2.4 m
Printer:
15 feet / 4.6 m
Cable length loss must be factored in if equipment is
installed in a raised-floor environment. Part of the
cable length is routed inside the equipment to
connect with interior power receptacles.
All power cords attach to the back of the printer.
Listed below are the distances of the printer power
cord attachments from the left end of the printer as
you face it:
Cord #1: 36 inches / 914 mm
Cord #2: 23 inches / 584 mm (DP 155 & 180)
Special considerations
Transference of the black toner to poly-vinyl
surfaces is a common occurrence.
When printing edge to edge, there is a 3 to 4.8 mm
border around the sheet where degraded image
quality may occur.
Edge marking should be no closer than 4.8 mm from
the edge of the sheet.
Xerox carbonless paper is approved for Xerox
DocuPrint 100/115/135/155/180 EPS. Refer to the
Xerox Supplies Catalog for the reorder numbers.
Appearance of very small spots is a common
occurrence on all xerographic printers. Consult your
Xerox service representative for details on
acceptable spot occurrence specifications.