Alderlea T4 설치 및 운영 매뉴얼 - 페이지 14

{카테고리_이름} Alderlea T4에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Alderlea T4 20 페이지. Cast iron wood stove

페이지 인쇄

Restarting After Extended or Overnight Burns

Open door and rake hot embers towards the front of the heater. Add a couple of dry,

split logs on top of embers, close door.

2. Adjust air control to high (left position) and in just a few minutes, logs should begin

burning.

3. After wood has charred, reset air control to desired setting.

4. To achieve maximum fi ring rate, set control to high (left position). Do not use this setting

other than for starting or preheating fresh fuel loads.

More Wood, More Heat

Seasoned wood has approximately 7500 BTU's per pound. If you put 10 pounds of wood

in your stove for an eight hour burn the wood will be producing 9375 BTU's per hour. (7500

BTU x 10 lbs./8hrs.=9375 BTU's per hr.) If you put 20 lbs of wood in your stove for eight

hour burn you will get 18,750 BTU's per hr. (7500 BTU x 20lbs./8hr.=18,750 BTU's per hr.).

This is only an example and is based on 100% efficiency. In reality your stove will operate

above the 80% range.

Experience will give you the right settings for proper combustion and efficient burning.

Remember the correct air inlet setting is affected by variables such as type of wood, outside

temperature, chimney size and weather conditions. With practice, you will become profi cient

in operating your heater and will obtain the performance for which it was designed.

Proper Draft

Draft is the force which moves air from the appliance up through the chimney. The amount

of draft in your chimney depends on the length of the chimney, local geography, nearby

obstructions and other factors.

2. Too much draft may cause excessive temperatures in the appliance. An uncontrollable

burn or a glowing red stove part or chimney indicates excessive draft.

3. Inadequate draft may cause backpuffing into the room and plugging of the chimney.

Smoke leaking into the room through appliance and chimney connector joints indicates

inadequate draft.

Ash Removal

Whenever ashes get 3 to 4 inches deep in your fi rebox, and when fi re has burned down

and cooled, remove excess ashes. Leave an ash bed approximately 1" (25 mm) deep on

the fi rebox bottom to help maintain a hot charcoal bed.

Ash Chute Operation: Your Alderlea stove is equipped with an ash chute system to ease

removal of ash from the ash lip area. To use this system, fi rst pull out the ash pan approxi-

mately 2" , sweep the ash into the chute located to the right side of the ash lip, and close

the ash pan.

Ash Cleanout System: The ash dump handle is located under the ash lip on the left hand

side. To operate ash dump, pull handle out 1/2" and turn clockwise. This will unlock the ash

dump and allow it to open. Hold handle open while pulling ashes into the opening. Avoid

large embers as these still contain heat value. Release handle and push in to lock. Ensure

ash dump door is properly engaged. Fill the cavity with the remaining ash level with the

fi rebox fl oor. Pull out ashpan and discard ashes into metal container. Replace ashpan and

ensure it is seated properly.

DO NOT OVERFIRE THIS HEATER:

Attempts to achieve heat output rates that

exceed heater design specifi cations can

result in permanent damage to the heater

and chimney.

CAUTION:

Ashes are to be removed only when the

heater is cold.

Do not burn with ash dump door open.

Doing so will create a hazardous

condition. Always leave about 1" of ash

when cleaning.

230611-20 ALT4