eControls C365T21WF 설치 프로그램 및 사용자 설명서 - 페이지 12

{카테고리_이름} eControls C365T21WF에 대한 설치 프로그램 및 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. eControls C365T21WF 13 페이지.

페이지 인쇄

USER OPTIONS (Continued)

Clean the Touch Screen

This option disables the touch screen for 30

seconds to enable the user to clean the touch

screen by wiping down with a soft, damp cloth.

Touch the MENU key

to display CLEAN

DISPLAY option

indicated by CL. To

exit this option, press

NEXT.

ENTER

Press ENTER to start

the 30 second count

down. The touch

OFF

screen is disabled

during this time.

HELPFUL HINTS FOR HOMEOWNERS

What are common settings for my thermostat?

Many homeowners run their thermostat in the HOLD mode. Set

the HOLD mode by touching the MODE key until HOLD is

displayed. Now select the SYSTEM mode and adjust your set

point. In COOL the thermostat will turn on cooling when the

room temperature is at or above the set point temperature. In

HEAT the thermostat will turn on heating when the room

temperature is at or below the set point temperature.

If your household follows a set schedule, the SCHEDULE mode

can be selecting by touching the MODE key until SCHEDULE is

displayed. The thermostat will now follow the default schedule

or a custom schedule set by the homeowner.

Does the Comfort365 have any energy saving

features?

One of the biggest energy saving features is the Nighttime

Airflow Control option which can save 30% in energy at night.

This option is defaulted to On and is ideal when all of the

bedrooms are located upstairs. This option uses the

temperature sensors in the sleeping area to make heating and

cooling calls. In addition, the thermostat automatically directs

130% more airflow to the sleeping space and 30% less airflow

to the unoccupied living space.

How do I display the sleeping space

temperature?

Touch the area where Living and the room temperature is

displayed. The thermostat will now display the sleeping space

temperature. Touch the area again to display the living space

temperature.

If the sleeping space temperature is unusually low or high,

contact your installer. The wrong type of sensors may have been

installed or the sensors may have been wired incorrectly.

Note: If Nighttime Airflow Control option is On, the thermostat

will automatically display the sleeping temperature at the Night

start time.

Warranty

This thermostat is warranted to be free of defects due to workmanship

or materials under normal use and service for a period of 5 years from

date of installation and not longer than 6 years from manufacturing

date code.

HOMEOWNER SECTION

Broadcasts WiFi Network

See Homeowner WiFi Quick Start Quide for

information on setting up WiFi. This option always

defaults to Off. Turning the option to ON

broadcasts the thermostat WiFi network for 30

minutes to allow for set up.

ENTER

eControls, Inc. 26072 Merit Circle #110 / Laguna Hills, CA 92653

INSTALL / REPLACE AA BATTERIES

Two AA batteries power

the clock when 24VAC

power is lost. Slide the

battery cover downward

and install the two AA

batteries, paying

attention to the polarity.

How do I direct more airflow to the downstairs

living space or upstairs bedroom space.

The thermostat automatically controls airflow to the living and

sleeping space. However, the thermostat includes options to

allow the homeowner to direct more airflow to either the living

space or the sleeping space.

Override Airflow for 3 Hours

Touch the Airflow % area. The set point disappears. Use the UP

key to increase airflow to the sleeping space or the DOWN key

to increase airflow to the living space. To end airflow override,

touch the Airflow % area, then touch the MODE key.

Override Airflow Permanently (Manual Control)

Touch the MENU key twice to display the AAC option. This

option, Automatic Airflow Control, defaults to On. Turn OFF by

touching the DOWN key. Manually change the airflow by

touching the Airflow % area and using the UP or DOWN key to

direct airflow to the living or sleeping space. The airflow % will

remain until the homeowner makes an adjustment.

Note: If Nighttime Airflow Control is On, at the morning start

time when Nighttime Airflow Control ends, the airflow % will

change to 100%. This prompts the homeowner to evaluate the

airflow needs for that day.

My airflow doesn't seem to be working properly.

Test the airflow by overriding the airflow (See above). Increase

the airflow to the sleeping space to the maximum. You should

feel more airflow coming from the registers in the sleeping

space compared to the registers in the living space. Now

increase the airflow to the living space to the maximum. You

should feel more airflow coming from the registers in the living

space compared to the registers in the sleeping space.

If you do not get these results, contact your installer.

Learn more about your Comfort365 Thermostat at

Comfort365USA.com. Click on Quick Tip Videos.

949-916-0945 Fax 949-458-8502 www.eControlsUSA.com

eControls