Yamaha AW4416 매뉴얼 보충 자료 - 페이지 12
{카테고리_이름} Yamaha AW4416에 대한 매뉴얼 보충 자료을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha AW4416 48 페이지. Installing an internal hard disk
Yamaha AW4416에 대해서도 마찬가지입니다: 보충 설명서 (1 페이지), 튜토리얼 (34 페이지), 보충 설명서 (20 페이지), 매뉴얼 (3 페이지)
페이지 인쇄
AW4416 Version 2.0 Manual Supplement
If you select a category from the right column of
buttons (SCENE MEM.–REMOTE), move the cur-
sor to the column at the far right, and turn the
[DATA/JOG] dial to select the content within that
category that will be transmitted.
Category
AW4416 settings other than the
SETUP MEM.
following items
Settings of the MIDI screen PGM
PGM. TABLE
ASGN. page
Settings of the MIDI screen CTL
CTL. TABLE
ASGN. page
SCENE MEM.
The specified scene memory
PATCH LIBRARY
The specified patch library
CH LIBRARY
The specified channel library
EQ LIBRARY
The specified EQ library
DYN. LIBRARY
The specified dynamics library
EFF. LIBRARY
The specified effect library
AUTO MIX
The specified automix
MIDI REMOTE
Settings of the REMOTE screen
B
REQUEST button
When you move the cursor to this button and
press the [ENTER] key, a "bulk dump request"
message requesting the bulk dump data selected
in 1 will be transmitted from the MIDI OUT
connector/TO HOST connector/option slot.
This button is used when two AW4416 units are
connected by their respective MIDI IN/OUT con-
nectors, and you want to copy scene memory or
library data from one unit to the other.
C
TRANSMIT button
When you move the cursor to this button and
press the [ENTER] key, the bulk dump will begin.
D
INTERVAL
This adjusts the interval that will be left between
data blocks when bulk data is transmitted. You
can set the interval in 1 millisecond units over a
range of 0–300 milliseconds (default= 0).
3
Move the cursor to the button for the bulk
data that you want to transmit, and press
the [ENTER] key.
The corresponding button will be turned on, and
will be selected for bulk dump.
12
01–96
Scene number 1–96
EDIT BUFFER
Current scene (current mixer settings)
ALL
All scene memories + current scene
01–20
Library number 1–20
ALL
All patch libraries
02–64
Library number 2–64
ALL
All channel libraries
41–128
Library number 41–128
ALL
All EQ libraries
41–128
Library number 41–128
ALL
All dynamics libraries
42–128
Library number 42–128
ALL
All effect libraries
1–16
Memory number 1–16
BUFFER
Current automix
ALL
All automixes + current automix
REMOTE A–
Settings of the REMOTE A (REMOTE A 1-8/9-16
REMOTE B
pages) or B (REMOTE B 1-8/9-16 pages)
ALL
Settings of all pages of the REMOTE screen
4
If you selected a SCENE MEM.–REMOTE
button, move the cursor to the numerical
box at the right of the button, and use the
[DATA/JOG] dial to select the internal set-
tings that you want to transmit.
Tip!
If you move the cursor to the ALL button located at
the lower left of CATEGORY and press the [ENTER]
key, all settings that can be bulk-dumped will be
selected.
5
Put your MIDI sequencer in record-ready
mode.
When recording bulk data on your MIDI sequencer,
make sure that the MIDI Thru function (sometimes
called "Patch Thru" or "MIDI Echo") of your MIDI
sequencer is turned off. If this function is on, the bulk
data transmitted from the AW4416 will be immedi-
ately sent back to the AW4416, causing malfunctions.
Version 2.0 Manual Supplement
Values
—
—
—