Yamaha AW4416 매뉴얼 보충 자료 - 페이지 28
{카테고리_이름} Yamaha AW4416에 대한 매뉴얼 보충 자료을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha AW4416 48 페이지. Installing an internal hard disk
Yamaha AW4416에 대해서도 마찬가지입니다: 보충 설명서 (1 페이지), 튜토리얼 (34 페이지), 보충 설명서 (20 페이지), 매뉴얼 (3 페이지)
페이지 인쇄
MIDI screen
• List of parameters that can be assigned
Parameter 1 Parameter 2 Parameter 3
NO ASSIGN
Parameter 1 Parameter 2 Parameter 3
CHANNEL
MASTER
FADER
AUX 1 SEND
|
AUX 8 SEND
Parameter 1 Parameter 2 Parameter 3
ON
CHANNEL
MASTER
Parameter 1 Parameter 2 Parameter 3
PHASE
NOM/REV
Parameter 1 Parameter 2 Parameter 3
AUX 1 SEND
|
AUX 8 SEND
PRE/POST
Parameter 1 Parameter 2 Parameter 3
ON/OFF
TIME HIGH
DELAY
TIME LOW
• Parameters that are divided into (1) and (2) use two
control changes in conjunction. For example in order
to operate the dynamics processor HOLD parameter,
you must assign "REL/HOLD H" and "REL/HOLD L"
to separate control changes.
28
No parameter assigned
Operate the fader of the specified channel.
INPUT 1–24
Input channel 1–24
MONI 1–16
Monitor channel 1–16
RETURN 1/2
Return channel 1/2
Operate the stereo output channel fader or the AUX bus 1–8/bus 1–8
master level.
ST OUT
Stereo output channel
AUX 1–8
AUX bus 1–8
BUS 1–8
Bus 1–8
Operate the send level sent from the specified channel to AUX bus 1–8.
Parameter 2 specifies the send destination bus, and parameter 3 specifies
the channel.
INPUT 1–24
Input channel 1–24
MONI 1–16
Monitor channel 1–16
RETURN 1/2
Return channel 1/2
Control the on/off status of the channel [ON] key. Use parameters 2 and
3 to specify the desired channel.
INPUT 1–24
Input channel 1–24
MONI 1–16
Monitor channel 1–16
RETURN 1/2
Return channel 1/2
ST OUT
Stereo output channel
Switch the phase (normal/reverse) of the specified channel.
INPUT 1–24
Input channel 1–24
MONI 1–16
Monitor channel 1–16
RETURN 1/2
Return channel 1/2
Switch the pre-fader/post-fader settings of the signal that is sent from
each channel to AUX buses 1–8. Use parameter 2 to specify the bus, and
parameter 3 to select the desired channel.
INPUT 1–24
Input channel 1–24
MONI 1–16
Monitor channel 1–16
RETURN 1/2
Return channel 1/2
Control the delay of each channel. Use parameter 2 to select the param-
eter to be controlled, and parameter 3 to select the desired channel.
Delay on/off
Delay time ... (1)
Delay time ... (2)
INPUT 1–24
Input channel 1–24
MONI 1–16
Monitor channel 1–16
RETURN 1/2
Return channel 1/2
Version 2.0 Manual Supplement
Content
Content
Content
Content
Content
Content
• When using control changes to operate parameters,
it is not possible to switch the HIGH band EQ and
LOW band EQ parameters between shelving and low-
pass/high-pass filter.