Yamaha AW4416 매뉴얼 보충 자료 - 페이지 45

{카테고리_이름} Yamaha AW4416에 대한 매뉴얼 보충 자료을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha AW4416 48 페이지. Installing an internal hard disk
Yamaha AW4416에 대해서도 마찬가지입니다: 보충 설명서 (1 페이지), 튜토리얼 (34 페이지), 보충 설명서 (20 페이지), 매뉴얼 (3 페이지)

Yamaha AW4416 매뉴얼 보충 자료
FORMAT No. 01111110 7E
Universal Bulk Dump
01001100 4C
'L'
01001101 4D
'M'
00100000 20
' '
00100000 20
' '
00111000 38
'8'
01000011 42
'B'
00110011 39
'9'
00110110 38
'8'
DATA NAME
01000011 43
'C'
00100000 20
' '
EOX
11110111 F7
End Of Exclusive
4.13.3 Parameter Change
4.13.3.1 Basic format
STATUS
11110000 F0
System Exclusive Message
ID No.
01000011 43
Manufacturer's ID (YAMAHA)
SUB STATUS 0pppnnnn pn
p=mode (1:parameter change
or response for request
3:parameter request)
n=0-15(Rx Channel No.1-16)
GROUP ID
00111110 3E
MODEL ID(Digital Mixer)
MODEL ID
00001000 08
Device Code(AW4416)
PARAM TYPE 0ttttttt tt
Parameter type
DATA
0ddddddd dd0 data 0
:
:
0ddddddd ddn data n
EOX
11110111 F7
End Of Exclusive
Parameter
type
rx/tx
function
------+------+-----------------------------------
0x00
rx/tx
edit buffer (byte operation format)
0x01
rx/tx
setup memory (byte operation format)
0x02
rx/tx
function call (mem/lib recall,mem/lib
store)
0x10
rx/tx
edit buffer (7bit operation format)
0x40
rx/tx
edit buffer (bit operation format)
0x41
rx/tx
setup memory (bit operation format)
0x43
rx/tx
controller (key remote) (bit opera-
tion format)
4.13.3.2 Parameter Change
(byte operation for type 0x00:edit buffer)
4.13.3.2
< Reception >
This message is received if [Parameter Change RX] is ON
and the [Rx CH] matches the MIDI channel included in
the Sub Status.
This message will be echoed if [Parameter Change
ECHO] is ON.
When this message is received, the specified parameter
will be controlled.
< Transmission >
If [Parameter Change TX] is ON, this message will be
transmitted on the [Tx CH] MIDI channel when a param-
eter not specified in the [Control Change Assign Table] is
edited.
This message will be echoed if [Parameter Change
ECHO] is ON.
STATUS
11110000 F0
System Exclusive Message
ID No.
01000011 43
Manufacturer's ID No.
(YAMAHA)
SUB STATUS 0001nnnn 1n
parameter change or
response
Channel No.1-16)
GROUOP ID
00111110 3e
MODEL ID(digital mixer)
MODEL ID
00001000 08
Device code (AW4416)
PARAM TYPE 00000000 00
byte operation for edit
buffer (type)
DATA
0aaaaaaa dd1 address( H) high 7 bits of
14 bits address
0aaaaaaa dd2 address( L) low 7 bits of
14 bits address
0000dddd dd3 data( H) high 4 bits of 8
bits data
0000dddd dd4 data( L) low 4 bits of 8
bits data
:
:
continuous address datas
EOX
The range of valid addresses is 0x0000 - 0x0595.
4.13.3.3 Parameter Change
(7bit operation for type 0x10:edit buffer)
< Reception >
This message is received if [Parameter Change RX] is ON
and the [Rx CH] matches the MIDI channel included in
the Sub Status.
This message will be echoed if [Parameter Change
ECHO] is ON.
When this message is received, the specified parameter
will be controlled.
< Transmission >
If [Parameter Change TX] is ON, this message will be trans-
mitted on the [Tx CH] MIDI channel when a parameter not
specified in the [Control Change Assign Table] is edited.
This message will be echoed if [Parameter Change
ECHO] is ON.
STATUS
ID No.
SUB STATUS 0001nnnn 1n
GROUOP ID
MODEL ID
PARAM TYPE 00010000 10
DATA
EOX
The range of valid addresses is 0x0000 - 0x0595.
4.13.3.4 Parameter Change
(bit operation for type 0x40:edit buffer)
< Reception >
This message is received if [Parameter Change RX] is ON
and the [Rx CH] matches the MIDI channel included in
the Sub Status.
This message will be echoed if [Parameter Change
ECHO] is ON.
When this message is received, the specified parameter
will be controlled.
< Transmission >
If [Parameter Change TX] is ON, this message will be trans-
mitted on the [Tx CH] MIDI channel when a parameter not
specified in the [Control Change Assign Table] is edited.
This message will be echoed if [Parameter Change
ECHO] is ON.
STATUS
ID No.
SUB STATUS 0001nnnn 1n
n=0-15(MIDI
GROUOP ID
MODEL ID
PARAM TYPE 01000000 40
DATA
EOX
The range of valid addresses is 0x0000 - 0x0595.
Version 2.0 Manual Supplement
11110111 F7
End Of Exclusive
11110000 F0
System Exclusive Message
01000011 43
Manufacturer's ID No.
(YAMAHA)
parameter change
15(MIDI Channel No.1-16)
00111110 3e
MODEL ID(digital mixer)
00001000 08
Device code (AW4416)
7bit operation for edit
buffer (type)
0aaaaaaa dd0 address( H) high 7 bits of
14 bits address
0aaaaaaa dd1 address( L) low 7 bits of
14 bits address
0ddddddd dd2 data 7bit
:
:
11110111 F7
End Of Exclusive
11110000 F0
System Exclusive Message
01000011 43
Manufacturer's ID No.
(YAMAHA)
parameter change
15(MIDI Channel No.1-16)
00111110 3e
MODEL ID(digital mixer)
00001000 08
Device code (AW4416)
bit operation for edit
buffer (type)
0aaaaaaa dd0 address( H) high 7 bits of
14 bits address
0aaaaaaa dd1 address( L) low 7 bits of
14 bits address
0ddddddd dd2 data(bit0-2:change bit
no.0-7, bit3:0=reset
1=set)
:
:
11110111 F7
End Of Exclusive
n=0-
n=0-
45