Yamaha CP40 Stage 데이터 목록 - 페이지 34

{카테고리_이름} Yamaha CP40 Stage에 대한 데이터 목록을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha CP40 Stage 43 페이지. Stage piano

페이지 인쇄
Yamaha CP40 Stage 데이터 목록

MIDI Data Format

Many MIDI messages listed in the MIDI Data Format section are expressed in hexadecimal
or binary numbers. Hexadecimal numbers may include the letter "H" as a suffix. The letter
"n" indicates a certain whole number.
The chart below lists the corresponding decimal number for each hexadecimal number.
Decimal Hexadecimal
0
0
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
0A
11
0B
12
0C
13
0D
14
0E
15
0F
16
10
17
11
18
12
19
13
20
14
21
15
22
16
23
17
24
18
25
19
26
1A
27
1B
28
1C
29
1D
30
1E
31
1F
32
20
33
21
34
22
35
23
36
24
37
25
38
26
39
27
40
28
41
29
42
2A
43
2B
44
2C
45
2D
46
2E
47
2F
48
30
49
31
50
32
51
33
52
34
53
35
54
36
55
37
56
38
57
39
58
3A
59
3B
60
3C
61
3D
62
3E
63
3F
Additional Notes
• For example, 144 – 159(Decimal)/9nH/1001 0000 – 1001 1111(Binary) indicate the note-
on messages for the channels 1 through 16 respectively. 176 – 191/BnH/1011 0000 –
1011 1111 indicate the control change messages for the channels 1 through 16
respectively. 192 – 207/CnH/1100 0000 – 1100 1111 indicate the program change
messages for the channels 1 through 16 respectively. 240/F0H/1111 0000 is positioned
at the beginning of data to indicate a system exclusive message. 247/F7H/1111 0111 is
positioned at the end of the system exclusive message.
• aaH (Hexadecimal)/0aaaaaaa (Binary) indicates the data addresses. The data address
consists of High, Mid and Low.
• bbH/0bbbbbbb indicates byte counts.
• ccH/0ccccccc indicates check sums.
• ddH/0ddddddd indicates data/value.
Decimal Hexadecimal
64
40
65
41
66
42
67
43
68
44
69
45
70
46
71
47
72
48
73
49
74
4A
75
4B
76
4C
77
4D
78
4E
79
4F
80
50
81
51
82
52
83
53
84
54
85
55
86
56
87
57
88
58
89
59
90
5A
91
5B
92
5C
93
5D
94
5E
95
5F
96
60
97
61
98
62
99
63
100
64
101
65
102
66
103
67
104
68
105
69
106
6A
107
6B
108
6C
109
6D
110
6E
111
6F
112
70
113
71
114
72
115
73
116
74
117
75
118
76
119
77
120
78
121
79
122
7A
123
7B
124
7C
125
7D
126
7E
127
7F
SYNTHESIZER/SEQUENCER PART
(1) TRANSMIT FLOW
MIDI <-+-[SW1]--+---------NOTE ON/OFF
OUT
|
|
|
+---------CONTROL CHANGE
|
|
MODULATION
|
|
VOLUME
|
|
SUSTAIN SWITCH
|
|
EFFECT1 DEPTH (REVERB)
|
|
EFFECT3 DEPTH (CHORUS)
|
|
ASSIGNABLE CONTROLLERS
|
|
|
+--[SW4]--BANK SEL MSB
|
|
BANK SEL LSB
|
|
|
+--[SW5]--PROGRAM CHANGE
|
|
|
+---------PITCH BEND CHANGE
|
+--[SW2]-----------SYSTEM REALTIME MESSAGE
|
TIMING CLOCK
|
+------------------ACTIVE SENSING
|
+--[SW3]-+---------SYSTEM EXCLUSIVE MESSAGE
|
+---------<BULK DUMP>
|
F0H 43H 0nH 7FH mmH bhH blH ahH amH alH ddH....ddH ccH F7H
|
mm = CP4 STAGE: 1A, CP40 STAGE: 1B
|
+------------------SYSTEM EXCLUSIVE MESSAGE
IDENTITY REPLY
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH 06H 00H 00H 00H 7FH F7H
dd = CP4 STAGE: 49, CP40 STAGE: 4A
[SW1]
MIDI Transmit Channel
When Master Keyboard Switch is set to "off", MIDI data is transmitted via the specified channel for the current
Part.
When Master Keyboard Switch is set to "on", MIDI data is transmitted via the corresponding zone transmit
channels.
Program Change messages for changing Performances are transmitted over Basic Channel.
[SW2]
MIDI Clock Out
[SW3]
MIDI Device Number
When set to all, transmitted via 1.
[SW4]
SYSTEM Transmit/Receive Bank Select
[SW5]
SYSTEM Transmit/Receive Program Change
9nH
BnH, 01H
BnH, 07H
BnH, 40H
BnH, 5BH
BnH, 5DH
BnH, (01H .. 5FH)
BnH, 00H
BnH, 20H
CnH
EnH
F8H
FEH
CP4 STAGE/CP40 STAGE Data List
34