Yamaha DTX500 소유자 매뉴얼 - 페이지 34

{카테고리_이름} Yamaha DTX500에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha DTX500 48 페이지. Drum trigger module

페이지 인쇄

Trigger Setup Edit

Trigger Setup Edit contains various settings related to trigger input signals received from pads

or drum triggers (Yamaha DT20, etc.) that are connected to the trigger input jacks. These set-

tings let you optimize the DTX500 for best operation and response to these signals.

If you are using drum triggers attached to acoustic drums, or pads other than those that came

with the DTX500 set, you'll need to adjust the sensitivity. This section also has settings that help

prevent crosstalk* and double triggering*.

* Crosstalk: The interference between trigger signals of physically adjacent pads, producing unexpected notes.

* Double triggering: The condition where a single pad hit causes multiple (usually two) triggers.

Trigger Setup procedure

If you want to replace some of the pads from your drum set, or if

you need to solve problems with double triggering or crosstalk,

the Trigger Setup provides more detailed settings—such as

changing the preset's trigger setup—for individual pads.

If you've created a custom setup for these reasons or others, that

setup can be saved to one of the Trigger Setup locations (8–11).

Press the [SHIFT] + [DRUM KIT] buttons to call up the Trig-

ger Setup Select page (TRG1). The currently selected Trigger

Setup is indicated in the display.

* If you want to edit a different trigger setup, use the jog dial

and select the setup here.

Use pages TRG2 through TRG8 to edit the Trigger Setup.

Press the [

]/[

] buttons to change pages and move the

ﬂashing cursor to the parameter you want to set.

* Refer to pages 35 to 37 for more information on individual

parameters.

To select the Trigger Input (input jack) you want to edit, sim-

ply hit the pad you want to edit or use the [SHIFT] + [

[

] buttons.

TRG2~

"Type=SN-1~~~~~‚

Previous page icon

DTX500 Owner's Manual

Trigger Setup Select display (page 1)

TRG1~~~ååååååååå

1~:XP~Med~~~~~~‚

Trigger Setup Number: Setup Name

Trigger Input to be edited

ƒsnare~~0%

Next page icon

Flashing cursor (parameter)

Rotate the jog dial to change the setting.

* An asterisk "

is changed. This asterisk will disappear after the Store opera-

tion is carried out.

* The Trigger Input Level produced when a pad is hit is shown

on the upper right side of the display. When setting the gain,

use this level as a guide to measure how hard a pad is being

hit.

To save changes you've made to the data, use the procedure

described below to store them to a User Trigger Setup (8–11).

NOTICE

• If a different trigger setup is selected before executing

the Store operation, all changes you have made to the

data will be lost. If you want to keep settings or changes,

make sure to carry out the Store operation.

4-1.

Press the [SAVE/ENTER] button. The following dis-

play will appear.

4-2.

Rotate the jog dial to select the destination trigger

setup number (8–11).

4-3.

If you want to change the Trigger Setup name, press

the [

character you want to edit, then rotate the jog dial to

select a character. A Trigger Setup name can contain a

maximum of eight characters, and these can be

selected from the following list.

space

!"#$%&'()*+,-./0123456789:;<=>?@

ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`

abcdefghijklmnopqrstuvwxyz{|}≥≤

TRG

" will appear next to "

" in the display if data

Trigger Input Level

TRG2* ƒsnare~~0%

"Type=DT~Snare~‚

Store destination

TRG~save~to~8

:[XP~Med~~]

Trigger Setup name

]/[

] buttons to move the ﬂashing cursor to the