Yamaha YDP-88 소유자 매뉴얼 - 페이지 14

{카테고리_이름} Yamaha YDP-88에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha YDP-88 16 페이지. Yamaha digital piano owner's manual

페이지 인쇄

A voltage selector is provided

in some areas.

VOLTAGE

SELECTOR

• We do not recommend attempting to assemble the

NOTE

YDP-88 alone. The job can be easily accomplished,

however, with only two people.

• Use only the screws provided or replacements of

exactly the specified size. Using screws of the wrong

size can result in damage to the instrument.

Open the box and remove all the parts.

On opening the box you should find the parts shown in

the illustration above. Check to make sure that all the re-

quired parts are provided.

Attach the side panels (D) to the pedal

box (C).

Place the pedal box on top of the wooden blocks attached

to the side panels (D), align the rear surfaces, and attach

using the four 6 x 35 millimeter round-head screws 1 —

two screws on each side. Make sure the pedals extend in the

same direction as the feet.

Attach the rear panel (B).

With the rough surface of the rear panel facing outward

and the panel angled slightly as shown in the illustration,

lower it onto the screws protruding from the rear of the

pedal box so that the screws fit into the corresponding slots

in the lower edge of the rear panel. Then, while eliminating

any gaps between the rear and side panels, secure the top of

the rear panel to the side panel brackets using the two 4 x

10 millimeter round-head screws 2. Finally, tighten the

screws holding the rear panel to the pedal box.

Install the main unit (A).

Lay the completed stand on its side as shown in the illus-

tration. Stand the main unit (A) on its rear panel and posi-

tion it so that the screw holes on the bottom panel are

aligned with the brackets on the side panels of the stand.

Also center the main unit so that it extends an equal dis-

tance from both sides of the stand, as shown in the illustra-

tion. When the stand and main unit are properly positioned,

screw in and securely tighten the four 6 x 16 millimeter

flat-head screws 3.

Untie and unravel the pedal cord which is coiled and

attached to the bottom of the pedal box with a vinyl tie,

extend the cord and re-fasten it to the bottom of the pedal

box with the vinyl tie (see illustration).

Connect the pedal cord.

Raise the completed keyboard and stand assembly to its

normal playing position. Pass the pedal cord behind the rear

panel and plug the free end of the cord into the connector

on the bottom of the main unit (A). The plug only goes in

one way (the lug on the connector should face the rear of

the main unit, as shown in the illustration) — don't try to

force it in the wrong way around.

• A voltage selector is provided in some areas. To set

NOTE

the selector for 110V, 130V, 220V or 240V mains

voltages, use a "minus" screwdriver or similar imple-

ment to rotate the selector dial so that the correct

voltage appears next to the pointer on the panel.

Set the adjuster.

For stability, an adjuster is provided on the bottom of the

pedal box (C). Rotate the adjuster until it comes in firm

contact with the floor surface. The adjuster ensures stable

pedal operation and facilitates pedal effect control. If the

adjuster is not in firm contact with the floor surface, dis-

torted sound may result.

• After assembling the YDP-88, check once more to

IMPORTANT

make sure that all screws have been securely fas-

tened.

• If the stand leans to the side, makes unusual noises,

or otherwise seems unstable during use, check and

tighten all screws while following the assembly in-

structions given above.