Yamaha Arius YDP-V240 설치 매뉴얼 - 페이지 3

{카테고리_이름} Yamaha Arius YDP-V240에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha Arius YDP-V240 8 페이지. Yamaha arius ydp-v240 data list
Yamaha Arius YDP-V240에 대해서도 마찬가지입니다: 데이터 목록 (4 페이지)

Yamaha Arius YDP-V240 설치 매뉴얼

System Requirements

Data
Windows 2000/XP Home
Edition/XP Professional/
Musicsoft
Vista
Downloader
* Only 32-bit is supported.
Windows 7
Windows XP Professional
(SP2/SP3)/XP Home Edi-
tion (SP2/SP3)/2000 (SP4)
Windows XP Professional
x64 Edition (SP2)
USB Driver for
Windows Vista (SP0/SP1/
Windows
SP2)
Windows 7

Software Installation

If you have any problems with the installation, refer to
the troubleshooting section on page 5.
NOTE
• The example displays shown in this guide are in English.
Installing / Updating the USB-MIDI
Driver
In order to be able to communicate with and use MIDI
instruments connected to your computer, the appropri-
ate driver software must be properly installed on your
computer.
The USB-MIDI driver allows sequence software and
similar applications on your computer to transmit and
receive MIDI data to and from instruments via a USB
cable.
Computer
Sequence
software
USB Cable
Driver
Follow the steps below to install (or update) the USB-
MIDI driver.
1
Disconnect all USB devices from the
computer except for the mouse and
computer keyboard.
OS
Computer
233 MHz or higher; Intel
Pentium/Celeron Proces-
sor family
(500 MHz or higher is rec-
ommended)
166 MHz or higher; Intel
Core/Pentium/Celeron
processor
Intel 64 compatible pro-
cessor
800 MHz or higher; Intel
Core/Pentium/Celeron
processor or Intel 64 com-
patible processor
1.4 GHz or higher; Intel
Core/Pentium/Celeron
processor or Intel 64 com-
patible processor
MIDI instrument
Memory
128 MB or more
64 MB or more
(at least 512 MB
(256 MB or more is
of free space is
recommended)
recommended)
32 MB or more
(64 MB or more is
10 MB or more
recommended)
256 MB or more
10 MB or more
512 MB or more
10 MB or more
1 GB or more (32-
bit)/2 GB or more
10 MB or more
(64-bit)
2
Start the computer and use the "Admin-
istrator" account to log on to Windows.
Close all applications and windows that are open.
3
Insert the Accessory CD-ROM into your
computer's CD-ROM drive.
4
Turn off the power of the instrument.
5
Connect the USB connector of the com-
puter to the USB TO HOST terminal of
the MIDI instrument with a standard
USB cable.
NOTE
• Do not use a USB hub for connecting multiple USB
devices.
NOTE
• If you are using several MIDI instruments with USB con-
nection at the same time, connect all the instruments to
the computer and turn on the power for all of them, then
perform the following installation procedure.
6
Turn on the power of the instrument(s).
7
When the "Found New Hardware Wiz-
ard" window appears, click [Cancel].
NOTE
• On some computers, it may take a few minutes before
this screen appears.
Accessory CD-ROM for Windows Installation Guide
Hard Disk
Display
800 x 600
HighColor
(16-bit)
3