Yamaha THR30IIA Wireless 참조 매뉴얼 - 페이지 14
{카테고리_이름} Yamaha THR30IIA Wireless에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha THR30IIA Wireless 18 페이지.
Yamaha THR30IIA Wireless에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (5 페이지), 빠른 매뉴얼 (2 페이지)
페이지 인쇄
Troubleshooting
No power
• Connect the power adaptor properly (see
• Make sure that the THR30IIA Wireless been
properly charged, when the power adapter is
disconnected (see
page
No sound
No guitar sound is output (wired connection)
• Properly connect the guitar to the [GUITAR] jack
(see
page
7).
• Make sure that the volume control on the guitar
is turned up properly.
• Make sure that the [VOLUME] knob is not set to
the minimum (see
pages 4,
• When the [TONE SELECT] knob is set to FLAT,
make sure that the [TONE BLEND] knob is not
set to the minimum (see
• Make sure a set of headphones is not con-
nected to the [PHONES] jack; otherwise, sound
will not be output from the speaker on the
THR30IIA Wireless (see
• Make sure that the COMPRESSOR Level is not
set to 0 on the THR Remote app (see
13).
• Set the Tuner function OFF (see
• Make sure that the cable connecting the guitar
is not damaged.
No guitar sound is output (wireless con-
nection)
• Use the Relay G10T. THR30IIA Wireless cannot
connect to any guitar wireless transmitter other
than the Relay G10T.
• Connect the Relay G10T to the [GUITAR] jack
located on the top of the THR30IIA Wireless for
at least 10 seconds. The appropriate channel is
set automatically.
• Make sure that the volume control on the guitar
is turned up.
• Set the Tuner function OFF (see
page
8).
8).
5).
page
4).
page
5).
pages 11,
page
3).
page
3).
No sound is output from mic or electronic
musical instrument
• Properly connect the mic or electronic musical
instrument to the [MIC/INST] jack (see
• Make sure that the volume control on the elec-
tronic musical instrument is turned up properly.
• Use only a dynamic microphone; the THR30IIA
Wireless cannot supply phantom power if a con-
denser microphone is connected.
No audio from Bluetooth source
• Confirm the status of the LED display. When the
LED is unlit or flashing in green, the devices are
not connected via Bluetooth (see
• When the Bluetooth configuration on the smart
device is ON, turn it OFF once and configure
"Playing audio files on a smart device via Blue-
tooth" (see
page
10).
• Delete the Bluetooth registration once on the
Bluetooth configuration screen on the smart
device and configure "Playing audio files on a
smart device via Bluetooth" (see
• Move the smart device and the THR30IIA Wire-
less closer together.
• Turn off the power of the THR30IIA Wireless
and turn on again (see
• Restart the smart device.
* For details on Bluetooth configuration, refer to the
manual of the smart device.
• Disconnect any other Wi-Fi and Bluetooth
devices. The connection may be disrupted due
to the influence of other nearby Wi-Fi or Blue-
tooth devices.
No audio sound is output from a computer
by USB connection
• Properly connect the USB cable (see
• Confirm the configuration of the audio output
port on the computer (see
• Confirm the configuration of the computer on
the computer or that audio is not muted on the
application.
• Make sure the USB cable connecting the
devices is not damaged.
THR30IIA Wireless
page
7).
page
17).
page
10).
page
8).
page
12).
page
12).
Reference Manual
14