Yamaha ATS-1010 소유자 매뉴얼 - 페이지 16

{카테고리_이름} Yamaha ATS-1010에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Yamaha ATS-1010 20 페이지. Front surround system
Yamaha ATS-1010에 대해서도 마찬가지입니다: 소유자 매뉴얼 (19 페이지)

페이지 인쇄

Refer to the chart below should the unit not function properly. If the problem you are experiencing is not listed below,

or if the instruction below does not help, set the unit to the standby mode, disconnect the AC power supply cable, and

contact the nearest authorized Yamaha dealer or service center. Check the below first.

1 The AC power supply cable of the unit, TV and external components (such as BD player) are firmly connected to

the AC wall outlet.

2 The power supply of the unit, TV and the external components (such as BD player) are turned on.

3 All cables are firmly connected to their respective jacks on each component.

Problem

Power turns on but

immediately shuts off.

The speakers make no

sound.

Surround effect is not

achieved.

No bass / The external

subwoofer makes no sound.

The volume level decreases

without any operation.

This unit does not operate

properly.

A digital or high-frequency

equipment produces noises.

The remote control does not

operate the unit.

The volume of the unit and TV

increases simultaneously.

Troubleshooting

Cause

The power cable may be connected improperly. Make sure the power cable is plugged into the

The unit may have received a strong electrical

shock, such as from a lightening bolt or

excessive static electricity.

The unit has an auto-sleep function, which will

automatically set to standby mode if the unit is

left turned on for 12 hours without any

operation being performed.

The volume may be set to minimum.

The mute function may be activated.

The input source or input setting may be

incorrect.

A surround mode is not selected.

The volume of the subwoofer channel may be

set to minimum level.

Opposite setting of subwoofer is selected.

The source does not contain low frequency

signals.

The cable between the unit and the subwoofer

not connected when selecting playback of the

external subwoofer.

The unit controls its volume within a certain

level to prevent the next playback from sudden

output at excessive volume.

The unit may receive a strong electrical shock,

such as from a lightening bolt or excessive static

electricity, or drop in power supply.

The unit may be placed close to digital

equipment or high-frequency equipment.

The unit may be outside the remote control

operation range.

The remote control sensor of the unit may be

exposed to direct sunlight or other lighting.

The batteries may be worn out.

Your TV itself received the signal from TV

remote control, having learned the operation of

the unit.

Solution

outlet firmly.

Set the unit to standby mode, and then

disconnect the power cable. Wait for about 30

seconds, connect the power cable, and then turn

the unit on again.

Adjust the volume level.

Press MUTE on the remote control to cancel the

mute function and adjust the volume.

Select the correct input source or input setting.

Press SURROUND on the remote control to

play back the source in surround effect.

Adjust the volume level of the subwoofer.

Select collect setting of subwoofer.

Connect the unit and the external subwoofer by

using a subwoofer pin cable.

Reset the volume.

Set the unit to standby mode, and then

disconnect the power cable. Wait for about 30

seconds, connect the power cable, and then turn

on the unit again.

Place the unit away from such equipment.

The operation range for the remote control of

the unit is within 6 m (20 ft).

Change the lighting or reposition the unit.

Replace the batteries.

Set the volume of your TV to minimum, or set

the audio output of your TV built-in speaker to

off.

Adjust the volume by using the remote control

of the unit.

See

page

—