Clark Synthesis TST329 설치 매뉴얼 - 페이지 6
{카테고리_이름} Clark Synthesis TST329에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Clark Synthesis TST329 8 페이지. Platinum, gold, silver and all weather transducers
Clark Synthesis TST329에 대해서도 마찬가지입니다: 보충 설명서 (4 페이지), 데이터시트 (1 페이지), 구매자 매뉴얼 (2 페이지), 설치 매뉴얼 (20 페이지), 사양 (1 페이지), 설치 매뉴얼 (20 페이지)
페이지 인쇄
Installation: Overview
Installation Type: Unimount Bracket
Screws into the bottom of the mounting surface.
Requires access only to the bottom of the mounting
surface. Requires a flat or nearly flat mounting surface.
Min. 4-1/2"
vertical space
required,
including 1/2"
clearance
between the
Transducer
and floor.
3/4"-thick
mounting
surface
Unimount
Bracket
Flat Washer
Lock Washer
Screw
Jam Nut (up)
3/8"-16
Threaded Stud
Jam Nut (down)
Transducer Wire Lead
Washers
Machine Screw
Jam Nuts
tactile sound transducer
5
Installation Type: Hanger Bolt
Screws into the bottom of the mounting surface (into a
5/16" drilled hole). Requires access only to the bottom of
the mounting surface.
Min. 3-1/4" vertical space
required, including 1/2"
clearance between the
Transducer and floor.
Joist
Minimum
(edge view)
3/4"-thick
Drill 5/16" hole
Tip: Tighten
two Jam Nuts
3/8"-16
against each
Hanger Bolt
other to screw
in Hanger Bolt
Jam Nut (down)
using wrench.
NEVER TIGHTEN
BY TURNING THE
TRANSDUCER.
MAKE SURE TO
Transducer Wire Lead
NUT
TIGHTEN THE JAM
NUT AGAINST THE
TRANSDUCER'S
BRASS NUT.
Jam Nut
www.clarksynthesis.com
Installation Type: Hanger Bolt
The AW339-All Weather Transducers are recommended for use
on outdoor installations, including decks, boat docks, etc.
For decks, we recommend using one (1) All Weather Transducer
for every 10 ft. by 10 ft. section of deck. For example, if you have
a deck that measres 10 ft. by 30 ft., we would suggest you install
three (3) Transducers.
For all installations, regardless of the number of Transducers, we
recommend locating the Transducers equidistant from the edges
of the deck and/or from each other. This helps create a more
uniform distribution of the tactile effect.
The easiest installation method is to use the Hanger Bolt to mount
the Transducer(s) to the bottom of the joist(s). Steps for this
installation method can be found on Page 8.
Note: If for some reason it is not possible to mount to the joists,
use a bridge between joists as you would in a floor installation
(see Page 8 for instructions and images for building a bridge).
It is important to make Transducer wire connections as watertight
as possible by using electrical tape and molded plastic connectors.
www.clarksynthesis.com
Installation: Wood Decks
Deck joists 16" - 24" on center
TST mounts directly to bottom of joist using Hanger Bolt
MOUNTING DETAIL
joist
(edge view)
Hanger Bolt
Jam Nut
Tip: Tighten two
Jam Nuts against
each other to
screw in Hanger
Bolt using wrench.
tactile sound transducer
10