Clark Synthesis TST329 설치 매뉴얼 - 페이지 8

{카테고리_이름} Clark Synthesis TST329에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Clark Synthesis TST329 8 페이지. Platinum, gold, silver and all weather transducers
Clark Synthesis TST329에 대해서도 마찬가지입니다: 보충 설명서 (4 페이지), 데이터시트 (1 페이지), 구매자 매뉴얼 (2 페이지), 설치 매뉴얼 (20 페이지), 사양 (1 페이지), 설치 매뉴얼 (20 페이지)

페이지 인쇄

Installation: Chairs & Couches

NOTE: If your chair or couch cannot accommodate a Transducer, consider

purchasing or constructing a platform (see "Platforms" on Page 8).

As a general rule, most chairs and couches have an underlying wooden

frame. The Transducer can be mounted directly to a frame member or to a hard

wood bridge (see diagram) that is rigidly secured to the chair's/couch's base. The bridge

should be at least 3/4" thick and cut to span two frame members or connect two sides

of a box frame. The more centrally located the frame member or bridge is on

the overall structure, the better the distribution of tactile sound.

CAUTION: When used in recliners, make sure that the Transducer and its

wire do not interfere with the recliner's mechanical elements. Also, a

minimum clearance from floor to mounting surface for these types of installs is

4-1/2 inches for the Unimount Bracket and 3-1/2 inches for the T-Nut.

Steps for installation using the Unimount Bracket

1. Attach the Unimount Bracket to the mounting surface using machine

screws with flat washers and lock washers.

2. Screw a Threaded Stud into the threaded insert on the Unimount

Bracket.

Spin the two Jam Nuts onto the stud. You will tighten them later.

Screw the Transducer onto the Stud until slight resistance is felt

(approx. 5 or 6 turns). When resistance is felt, stop turning.

•

DO NOT OVERTIGHTEN THE TRANSDUCER!

Tighten one Jam Nut against the threaded insert of the Unimount

Bracket.

Tighten the other Jam Nut against the Transducer's brass nut using two

9/16" wrenches as follows: One wrench firmly grasping the Transducer's brass

nut while the second tightens the Jam Nut against it.

•

NEVER TIGHTEN BY TURNING THE TRANSDUCER – MAKE SURE TO

TIGHTEN THE JAM NUT AGAINST THE TRANSDUCER'S BRASS NUT.

7. Use solder or wire nuts to connect the necessary length of speaker

wire to the Transducer's wire leads.

8. Run the speaker wire to your audio system.

9. Connect the Transducer to your audio system (see "Wiring and Connections"

later in this guide).

Steps for installation using the T-Nut Method

1. Drill a 7/16" hole in the mounting surface, being careful not to drill through existing

springs, padding, strapping, etc. Press the T-nut into the hole on the side

of the mounting surface opposite the Transducer (see diagram).

2. Screw a Threaded Stud completely into the T-Nut.

Place the 3/8" flat washer and 3/8" lock washer on the Threaded Stud, then

spin the two Jam Nuts onto the stud (flat washer against the mounting surface, lock

washer between flat washer and jam nut). You will tighten the jam nuts later.

Screw the Transducer onto the Stud until slight resistance is felt

(approx. 5 or 6 turns). When resistance is felt, stop turning.

•

DO NOT OVERTIGHTEN THE TRANSDUCER!

Tighten one Jam Nut against the lock washer, flat washer, and mounting surface.

Follow steps 6 through 9 under "Steps for installation using the Unimount Bracket"

(as shown above).

tactile sound transducer

Installation Type: Unimount Bracket or T-Nut

Hardwood Bridge (min. 3/4" thick)

Transducer mounts on hardwood bridge attached to chair

frame, or to a centrally-located frame member, if present.

Bridge should be min. 3/4" thick and 6" – 8" wide.

MOUNTING DETAIL

Washers

Jam Nuts

Screws

Using Unimount Bracket

MOUNTING DETAIL

T-Nut

Washers

Jam Nuts

Using T-Nut

www.clarksynthesis.com

Installation: Traditional Floors & Platforms

Installation Type: Hanger Bolt

TRADITIONAL FLOORS

If you want to use Transducers under the floor to supplement a music

system, then you should seek an evenly distributed effect. Transducers

may be mounted under a floor by attaching a bridge connected between

adjacent floor joists.

If your goal is to activate the area of the floor directly beneath a chair,

then attach the Transducer to the closest joist underneath the chair.

Note: Carpeting and padding may reduce the tactile effect.

PLATFORMS

Recommendation: Clark Synthesis recommends using only TST429-Platinum

Transducers for platforms. Use of (1) TST429-Platinum for every 4 ft. by 8 ft.

section of platform is suggested.

Platforms are a great alternative to mounting a Transducer directly to a

chair. This method is especially practical in home theaters with multiple rows

of seating where back rows are elevated on a riser. An activated platform

will deliver tactile sensations to your feet as well as the rest of your

body via the chair.

Whether constructing a new platform or fitting Transducers onto an existing

platform, it is best to space the Transducers equidistant from each other and the

edges of the platform. If using only one Transducer, locate it in the

center of the platform.

To minimize energy loss into the floor, use Isolation Feet between the

platform and the floor (see Page 2).

NOTE: Clark Synthesis does not recommend using MDF

(medium-density fiberboard) in a platform.

Steps for installation using the Hanger Bolt

1. Drill a 5/16" hole in the wood mounting surface

and screw in the pointed end of the Hanger Bolt

until it is secure.

2. Spin one Jam Nut onto the Hanger Bolt approximately 1".

3. Screw the Transducer onto the Hanger Bolt until slight resis-

tance is felt (approx. 5 or 6 turns). When slight resistance is

felt, stop turning.

•

DO NOT OVERTIGHTEN THE TRANSDUCER!

4. Tighten the Jam Nut against the Transducer's

brass nut using two 9/16" wrenches as follows: One

wrench firmly grasping the Transducer's brass fastener

while the second tightens the Jam Nut against it.

•

NEVER TIGHTEN BY TURNING THE TRANSDUCER

– MAKE SURE TO TIGHTEN THE JAM NUT

AGAINST THE TRANSDUCER'S BRASS NUT.

5. Use solder or wire nuts to connect

speaker wire to the Transducer's wire leads.

6. Run the speaker wire to your audio system.

7. Connect the Transducer to your audio system (see

"Wiring and Connections" later in this guide).

www.clarksynthesis.com

Floor joists 16" on center

Tip: Tighten two

Jam Nuts against

each other to

screw in Hanger

Transducer mounts using Hanger Bolt on

Bolt using wrench.

2"x 6" har dwood bridge between joists. If

vertical space is limited, cut a curved or

rectangular niche in the bridge for the

Transducer (see mounting detail). Attach the

bridge to the floor (adhesive) and to the joists

(adhesive and screws).

CAUTION: Do not cut curves in existing joists.

MOUNTING DETAIL

2"x 6" bridge with curved niche

Jam Nut

Glue and screw plywood

floor surface to all

frame members

including the bridge

Transducer mounts in niche

on 2"x 6" bridge using

Hanger Bolt

Glue & screw

all joints

2"x 6" inner joists

16" on center

2"x 8" outer joist

Constructing a platform for optimum Transducer Performance

Use 2" x 8" outside joists and 2" x 6" inside joists. The 2" difference in joist

height suspends the center of that platform above the actual floor, improving

distribution of the tactile vibrations. Use interior-grade plywood for the platform

surface. We highly recommend using adhesive and screws instead of

nails. Loose fitting joints can cause unwanted vibrations or buzzing noises,

particularly between the joists and the platform surface. Shown is a 4'x4'

platform, but you can make any size as long as the joists are spaced 24" or

16" on center to provide sufficient rigidity for tactile wave transmission.

tactile sound transducer