Directed Xpresskit DBALL2 설치 매뉴얼 - 페이지 5

{카테고리_이름} Directed Xpresskit DBALL2에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Xpresskit DBALL2 19 페이지. Ford5 remote start ready (rsr) installation
Directed Xpresskit DBALL2에 대해서도 마찬가지입니다: 설치 매뉴얼 (12 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 매뉴얼 (14 페이지), 설치 매뉴얼 (13 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (15 페이지), 설치 및 빠른 참조 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 매뉴얼 (19 페이지), 설치 매뉴얼 (11 페이지), 설치 매뉴얼 (10 페이지)

페이지 인쇄

Platform: DBALL2

Firmware: CHRYSLER7 Remote Start Ready Installation (RSR)

Installation without T-Harness

Important!

The Hood Pin and Remote Start Safety Override Switch are mandatory safety devices, but are NOT supplied with the DBALL.

Brake Connector

Brake:

Dk.Green/Lt. Green,

pin 1

Immo. Data:

White/Lt. Green, pin 5

PTS Switch

(+) PTS:

Violet/

(black connector)

Brown,

pin 4

(-) Driver Door Trigger: Violet

Harness

in driver kick panel

Remote Start Safety Override Switch: If grounded, the vehicle will NOT start.

[1]

HS CAN2 connections are required for heated seats.

[2]

Hood pin: Required only when factory hood pin is not available.

[3]

With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).

(-) Ground: Black, pin 4

HS CAN2 High: Gray, pin 3

[2]

HS CAN2 Low: White, pin 11

[2]

HS CAN Low: Yellow, pin 14

(+) 12V: Red, pin 16

HS CAN High: Tan/Black: 3

HS CAN Low: Tan: 4

HS CAN2 High: Orange/Green: 5

[2]

HS CAN2 Low: Orange/Brown: 6

[2]

Immo. Data (vehicle side): Yellow: 8

Immo. Data (conn. side): Orange/Yellow: 9

(+) Brake Output: Yellow/Red: 11

(+) 12V: Brown/Red: 12

(+) 12V: Red: 13

(-) Ground: Black: 14

(+) PTS Output: Gray/Black: 7

(MUX) Parking Lights Output: Violet/Brown: 9

Immo. Data (vehicle side): Yellow/Black: 10

(-) RAP Off: Orange/Black: 11

Vehicle

Headlamp Switch

(6-pin Connector)

(MUX) Parking Lights:

White/Brown, pin 3

HS CAN High:Gray/White, pin 6

OBDII

Diagnostic

Connector

Prog. Button

DBALL2

LED

Rev.: 20160610

Hood Pin

[3]

Remote Start Safety

[1]

Override Switch

6: White/Black: (-) Hood

You can connect to either a XL202

RFTD OR a SmartStart module.

Refer to the SmartStart/XL202

Installation Notes for more information.

Page 4