Directed 4115V 빠른 참조 설치 매뉴얼

{카테고리_이름} Directed 4115V에 대한 빠른 참조 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed 4115V 2 페이지. Remote start with keyless entry

페이지 인쇄

Quick Reference Install Guide

Remote Start with Keyless Entry

4115V

Wiring Connections

Primary Harness, 9-pin connector

LIGHT GREEN BLACK

(-) 200mA FACTORY ALARM DISARM OUTPUT

GREEN/WHITE

(-) 200mA FACTORY ALARM REARM OUTPUT

YELLOW

(+) IGNITION OUT (TO ALARM)

WHITE/BLUE

(-) ACTIVATION INPUT

ORANGE

(-) 500mA GROUND WHEN LOCKED/ANTI-GRIND OUTPUT *

BROWN

(-) 200mA HORN OUTPUT

RED/WHITE

(-) 200mA TRUNK RELEASE OUTPUT **

BLACK

GROUND INPUT

WHITE

(+/-) LIGHT FLASH OUTPUT

* With the 1 button remote, the ground when locked feature is not available,

however this wire will still function as an anti-grind output during the remote start

sequence.

** Option not available on 1- button

Door Lock, 3-pin connector

LIGHT BLUE

(-) UNLOCK OUTPUT

EMPTY

NOT USED

GREEN

(-) LOCK OUTPUT

Red 4-pin port, Bitwriter/ ESP2 or D2D

Side View

Heavy

Gauge

Relay

Satellite Harness

Remote Start harness, 5-pin connector

BLACK/WHITE

(-) NEUTRAL SAFETY SWITCH INPUT

VIOLET/WHITE

TACHOMETER INPUT

BROWN

(+) BRAKE SHUTDOWN INPUT

GRAY

(-) HOOD PIN SWITCH SHUTDOWN INPUT

BLUE/WHITE

(-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT

Heavy Gauge Relay, 6-pin connector

PINK

OUTPUT TO PRIMARY IGNITION CIRCUIT

PURPLE

OUTPUT TO STARTER CIRCUIT

ORANGE

OUTPUT TO ACCESSORY CIRCUIT

RED

(+) (30A) HIGH CURRENT 12V INPUT

PINK/WHITE

OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT

RED

(+) (30A) HIGH CURRENT 12V INPUT

Satellite harness - 4-pin connector

BLUE

(-) 200mA STATUS OUTPUT

ORANGE

(-) 200mA ACCESSORY OUTPUT

PURPLE

(-) 200mA STARTER OUTPUT

PINK

(-) 200mA IGNITION OUTPUT

Parking light jumpers

Antenna

Side View

LED (Programming

indicator)

Control Button

(Valet Switch)

Door Lock/unlock

Harness

Antenna

4x03

Primary Harness

Remote Start Harness

Installation Points

Tach Learning

To learn the tach signal:

Start the vehicle with the key.

Within 5 seconds, press and hold the Valet (Control) button.

After 3 seconds the system LED will light constant when the tach signal is

learned.

Release the Valet (Control) button.

Important: This unit can learn the tachometer with the analog input or

through D2D using an interface module. The unit confirms which source

is used by flashing the parking lights.

When programming tach learning with:

•

Analog, the parking lights flash one time

•

D2D interface module, the parking lights flash twice

If the tachometer input on the system is connected to the vehicle, the D2D tachometer

input will be ignored.

Virtual Tach

Note: Virtual tach is not recommended for diesel vehicles.

To program Virtual Tach:

After the install is complete, remote start the car.

If the car does not start on the first attempt, let the remote start attempt again.

Once the car starts, let it run until the parking lights come on.

When the parking lights come on, shut off the remote start with the remote -

that's it! Virtual Tach is programmed.

Virtual Tach handles disengaging the starter motor during remote starting – it does

not address over-rev. If the customer wants to have the over-rev protection capabil-

ity, the tach wire must be connected. This may involve more installation shop

charges than initially quoted.

Important: If the Virtual Tach mode over cranks or doesn't crank the

vehicle long enough to start and run the car, use the Bitwriter to add or

subtract the starter output time. You can adjust the output time in incre-

ments of 50msec of the learned time using the Bitwriter.

Red 4-pin port, Bitwriter/ESP2 or D2D programming

The Red 4-pin plug may be configured as a Bitwriter/ESP2 or D2D port.

The factory default is Bitwriter/ESP2 mode.

To use as D2D mode follow the below steps:

Make sure White/Blue activation wire is grounded.

Power the unit up. The system LED flashes for 5 seconds to confirm D2D mode

change.

Remove the White/Blue wire from ground.

To change from D2D to Bitwriter/ESP2 mode:

Make sure White/Blue activation wire is grounded.

Power the unit up, the system LED turns on solid for 5 seconds to confirm Bit-

writer/ESP2 mode change.

Remove the White/Blue wire from ground.

The procedure can be repeated to toggle from one mode to the other.

Important: If you power up the system with the White/Blue activation

wire ungrounded, the system LED will come on solid for 5 seconds indi-

cating the system is in Bitwriter/ESP2 mode.

Remote Start Shutdown Diagnostics

The remote start module can inform you of what may have caused a remote start fail-

ure, if the remote start activates but fails to stay running. Before performing shutdown

diagnostics it is important that you let the remote start shut off on its own i.e. let it

attempt to start 3 times then shut down. Failure to do so causes the system to report

the shutdown you used to shut off the remote start.

Note: Shutdown diagnostics does not report if the vehicles factory immobilizer is

causing the problem

To perform shutdown diagnostics:

With the ignition Off, press and hold the Valet button.

Turn the ignition On and then back Off while holding the Valet button.

Release the Valet button.

Press and release the Valet button. The LED flashes to report the last

shutdown for one minute or until the ignition is turned on, as shown in the

following table:

LED Flashes

Shutdown Mode

1 flash

Timed out

2 flashes

Over-rev shutdown

3 flashes

Low or no RPM, low battery (voltage and virtual tach modes)

4 flashes

Transmitter shutdown (or optional push button)

5 flashes

(-) Hood Shutdown (5 pin RS harness GRAY)

6 flashes

(+) Shutdown (5 pin RS harness BROWN)

7 flashes

(-) Neutral safety shutdown (5 pin RS harness BLACK/WHITE)

8 flashes

Wait-to-start timed out

Guide Translations

For a Spanish or French version of the Installation Guide, please download it

from www.directechs.com under "Resources".

Traducción de los manuales:

Para obtener una versión en Español o Francés del Manual de Instalación,

descárguela de www.directechs.com bajo el título "Recursos" ("Resources").

Traduction du guide:

Pour une version française ou espagnole du guide d'installation, veuillez le

télécharger à www.directechs.com sous «Resources».

Bitwriters with a date code of 6a or older require an IC

upgrade (p/n 998M). Some bitwriters with a date code

of 6B do not require the IC upgrade, refer to tech tip #

1112 for more information.

The Bitwriter® (p/n 998U)

requires chip version 2.7 or

newer to program this unit.