Directed Directechs DB3 설치 매뉴얼 - 페이지 13

{카테고리_이름} Directed Directechs DB3에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Directechs DB3 20 페이지. Smart key for 2013 toyota highlander
Directed Directechs DB3에 대해서도 마찬가지입니다: 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 매뉴얼 (6 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (10 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (10 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (17 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지)

페이지 인쇄
Directed Directechs DB3 설치 매뉴얼

LED diagnostics and troubleshooting

This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation.
Module Programming
LED
Description
Module has no power.
Off
Waiting to begin the programming
Solid red
sequence.
Flashes green &
Initialization failed.
red
Transponder functions were skipped.
Solid orange
All required CAN networks has been
Flashes green
detected.
1 of 2 CAN networks has been detected.
Flashes orange
Flashes orange
Key2GO initiated.
slowly
Module was successfully programmed
Solid green x 3
with all functions.
secs
Module was successfully programmed
Solid orange x 3
without transponder functions.
secs
Module Programming - Error codes
LED
Description
CAN2 not detected.
Flashes red x 1
J1850 not detected.
Flashes red x 1
CAN1 not detected.
Flashes red x 2
Bypass data not detected.
Flashes red x 3
Bypass processing error.
Flashes red x 4
ISO 1 not detected.
Flashes red x 5
ISO 2 not detected.
Flashes red x 6
MUX not detected.
Flashes red x 7
External Module Synchronization
LED
Description
(Flashes red, red,
OBDII feature not supported.
then orange) x 10
13
403.HONDA9 1.12 2014 Acura RLX (Smart Key)
© 2020-02-28 Directed. All rights reserved.
Troubleshooting
Make sure the D2D harness is connected and that 12 Volt is present between the red and black
wires. If 12 Volt is present, the module may be defective.
Ensure the correct programming procedure is being followed.
Reset the module and complete the programming again. If the issue persists, please contact
Technical Support.
(If compatible) when RXT mode is not desired or convenience features are needed, please reset
the and reprogram the module.
Normal operation.
Normal operation.
Please follow the steps indicated in "Module programming" to complete the Key2GO
programming.
Normal operation.
Normal operation.
Troubleshooting
Check the CAN2 Orange/Green and Orange/Brown wire connections. Wake up the data bus
by turning the ignition on and try again. If your installation does not require this connection, skip
this step by pressing the programming button 5 times.
Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try
again.
Check the CAN1 Tan and Tan/Black wire connections. Wake up the data bus by turning the
ignition on and try again. If your installation does not require this connection, skip this step by
pressing the programming button 5 times.
Check the bypass line connection. If more than one wire is used, make sure they are not inverted.
Ensure the vehicle still operates correctly using the factory key.
The bypass calculation failed. Reset the module and try again. If the condition persists, please
contact Technical Support.
The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams
& vehicle wiring reference charts)" to check the connections.
The Orange/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams
& vehicle wiring reference charts)" to check the connections.
The Violet/Green or Violet/Brown wire did not detect the expected voltage value. Refer to
"Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.
Troubleshooting
The diagnostic data bus was not detected, therefore the SmartStart features will be limited.