Directed Directechs DB3 설치 매뉴얼 - 페이지 18

{카테고리_이름} Directed Directechs DB3에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Directechs DB3 19 페이지. Smart key for 2013 toyota highlander
Directed Directechs DB3에 대해서도 마찬가지입니다: 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 매뉴얼 (6 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (10 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (10 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (17 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (18 페이지)

페이지 인쇄
Directed Directechs DB3 설치 매뉴얼

Quick Reference Guide (customer copy)

Sending commands to your vehicle
Whether you want to remote start the engine, lock/unlock the doors or pop the trunk, there
are 3 possible ways you can send commands to your vehicle, using the:
1.
Factory remote.
2. Aftermarket remote.
3. Directed SmartStart
application via your smartphone.
®
If applicable, you can also start the engine remotely by pressing the Lock button 3 times
quickly on your factory remote.
Remote start attempts to mirror the OEM regardless of whether the vehicle has it installed. For
example, in some vehicles a maximum of two remote start commands are allowed (start with
remote and then shut down with remote are two separate commands). After that, the ignition
must be turned on and off before using remote start again. Refer to vehicle owners manual
for specific limitations.
Vehicle takeover
Close the vehicle doors, hood and trunk, then send the
1
Remote Start command to start the vehicle.*
Send the Unlock command on the factory or aftermarket
2
remote.*
Complete the following steps within 45 seconds or the vehicle will shut down.
Enter the vehicle.
3
Note: In a PTS vehicle, make sure the factory remote is
inside with you.
Insert your key in the ignition barrel and turn it to the ON
position.
4
OR
Press the PTS button once.
Depress the brake pedal, put the car in gear and drive
5
off.
* Icon and remote appearance may differ depending on the model purchased.
18
403.FORD12 2.07 2022 Ford Transit
©2023 Directed. All rights
Press Remote
Start button*
Press Unlock on
either remote*
Enter
vehicle
Key OUT
Key IN
Key IN
START
START
OR
Ready to
drive off
Pit stop/idle mode
The vehicle pit stop/idle mode feature is not available.
Conditions and Limitations
IMPORTANT: In the event of a module power cycle or vehicle battery disconnection or
Š
replacement, the ignition must be cycled to activate the Lock/Unlock functions for proper
functionality with aftermarket remote controls.
Š
The remote start system will not work in the following conditions:
Š The ignition is on.
Š The alarm system is triggered.
Š The doors/hood are open.
Š The transmission is not in Park (P).
Š The vehicle battery voltage is too low.
Š The service engine light is on.
Note: Any stored DTC code errors will prevent vehicle from remote starting (no visual
lights on dash).
Remote Start Ready (RSR)
Remote Start Ready (RSR) is a function that enables the interface module
14:36
to remote start the vehicle completely on its own. Consequently, there is
no need for an aftermarket or an OEM remote starter in order to start the
vehicle from a distance.
14:36
3x OEM Lock Remote Start Activation
This solution includes the option to remote start your vehicle by pressing the Lock button
3 times consecutively. If your vehicle allows the OEM remote to remain active while the
engine is running, you may shut down your remote starter by pressing the Lock button 3
times once more.
Note: The range offered by OEM remotes is limited and typically requires you to be within
Key IN
START
START
eyesight of the vehicle to control it.