Clarke Woodworker CJS2 운영 및 유지 관리 지침 - 페이지 6

{카테고리_이름} Clarke Woodworker CJS2에 대한 운영 및 유지 관리 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Clarke Woodworker CJS2 6 페이지. Variable speed jigsaw

페이지 인쇄
Clarke Woodworker CJS2 운영 및 유지 관리 지침

Changing Blades

Note :
Item numbers in brackets, refer to parts list on page 8.
With the power cable disconnected from the mains supply, slacken off the two hex
socket screws, (item 33), securing the Base Plate, using the hex. wrench stored at the rear
of the base of the tool, and ease the roller, (item 36), backwards away from the blade.
Loosen the two blade holder screws, (item 22), (accessed through the clear plastic blade
guard) and remove existing blade. Select the saw blade appropriate for the job in hand,
and insert it in to the Blade Holder as far as it will go, with the teeth facing forwards.
Tighten the two blade holder Hex socket screws progressively, until the blade is held firmly.
Push the roller forwards so that it just touches the back of the blade, and with the base
plate at the desired angle (this will normally be at 90°), tighten the two base plate
securing screws.

Operation

The ON/OFF trigger switch is located under the grip.
IMPORTANT: DO NOT plug in to the mains, unless you have ensured the tool is switched
OFF. To do this, pull the switch fully upwards, and then release it.
Push the clear plastic blade guard down fully.
To start the tool pull the trigger switch. Blade speed is dependant upon the pressure
applied to the trigger. The greater the pressure (ie the more it is pulled in) the greater the
speed. If you desire a constant speed, pull the switch all the way in and lock in position
with the knob on the side of the grip, then adjust the blade speed by turning the knob
(within the trigger switch) until you achieve the desired result. Wait until the blade is
running at its desired speed before attempting to cut the workpiece. To stop the tool if
the switch lock is activated, pull the trigger switch fully in, then release it, (motor will stop).
to make a cut, depress trigger, place the end of the base plate on the workpiece and
move it slowly forward along the cutting line. Take extra care when cutting curves - move
the blade slowly to avoid stress and therefore blade breakages.
The base plate is adjustable so that bevels of 15°, 30°,45° may be cut, however, if absolute
accuracy is required you should always check the angle with a protractor whilst carefully
tightening the two base plate securing screws. This includes setting the base plate for cutting
at 90°, (check roller is still only just touching blade).

Maintenance

Always inspect the tool before use, and ensure it is in top condition.
Ensure all air vents are clear, (use compressed air to clean the machine where possible).
Check the power cable to ensure it is sound and free from cracks, bare wires etc. avoid
using solvents when cleaning plastic parts, most plastics are susceptible to damage from
the various types of commercial solvents.
All bearings etc, in this tool are lubricated with a sufficient amount of high grade lubricant
for the tools lifetime under normal operating conditions, therefore no further lubrication is
required.
-5-
Trouble Shooting
Jig Saw is overheating
This indicates the machine is dirty. Clean the ventilation holes, and blow out with
compressed air or clean with a dry cloth.
Overloading the machine will also cause overheating. Do not use for heavy duty work,
and do not apply excessive pressure.
Excessive sparking occurs
This indicates worn brushes. This problem is quickly remedied but you should consult your
CLARKE dealer for parts and advice.
Jig Saw does not operate when switched ON
Check to ensure the fuse is sound and replace if necessary. If the fuse is sound or blows
repeatedly, consult your CLARKE dealer.

DUST EXTRACTION

The Jig saw is provided with a dust extraction facility, where a dust bag or vacuum extractor
may be connected to the rear of the machine. Please note however, that this does not
preclude the user from wearing a face mask to prevent the inhalation of dust particles.
It is an EEC requirement that a dust extraction facility be provided on power tools, however,
due to the nature of the tool, some of the dust produced will be forced into the surrounding
atmosphere, and will not be collected.
Parts & Service
For Spare Parts and Service, please contact your nearest dealer, or CLARKE
International, on one of the following numbers.
PARTS & SERVICE TEL: 020 8988 7400
PARTS & SERVICE FAX: 020 8558 3622
or e-mail as follows:
-6-