Zanussi FJ 831 지침 책자 - 페이지 9
{카테고리_이름} Zanussi FJ 831에 대한 지침 책자을 온라인으로 검색하거나 PDF를 다운로드하세요. Zanussi FJ 831 36 페이지. Zanussi washing machine instruction booklet
Zanussi FJ 831에 대해서도 마찬가지입니다: 지침 책자 (36 페이지)
페이지 인쇄INSTALLATION INSTRUCTIONS
If you intend the drain hose
from the machine to empty
into a sink, make sure that the
sink is empty and that the plug
hole is not blocked.
If
the
machine
is
permanently plumbed in, hook
the end of the drain hose into
a standpipe installed for the
purpose.
The standpipe must have an
internal diameter of at least
30 mm (1 1/2 in), in order that
there is an air gap between the
drain hose and standpipe.
Make sure, that it is designed
in such a way, that the end of
the drain hose cannot be
covered with water.
Important: Before connecting
up
the
machine
to
new
pipework or to pipework that
has not been used for some
time, run off a reasonable
amount of water to flush out
any debris that may have
collected in the pipes.
Whether discharging into a
sink or a standpipe check
that the end of the drain hose
is neither too high nor too
low. The top of the curve in
the hose's end should be no
more than 90 cm (35.4") and
no less than 60 cm (23.6")
above floor level.
ELECTRICAL CONNECTION
WARNING:
THIS APPLIANCE
MUST BE EARTHED
The manufacturer declines any
liability should this safety
measure not be observed.
If the plug that is fitted to
your appliance is not suitable
for your socket outlet, it must
be cut off and the appropri¬
ate plug fitted.
Remove the fuse from the
cut off plug. The plug should
then be disposed of to pre¬
vent the hazard of electric
shocks in case it should be
plugged
into
a
13
Amp
socket in another part of
your home.
Important
The wires in this mains lead
are coloured in accordance
with the following code:
GREEN AND
YELLOW
- EARTH
BLUE
- NEUTRAL
BROWN
- LIVE
If you fit your own plug,
the colours of the wires in the
mains lead of your appliance
may not correspond with the
markings identifying the
terminals in your plug, this is
what you have to do:
Connect the green and
yellow (earth) wire to the
terminal in the plug which is
marked with the letter «E» or
the earth
-Ar symbol or
coloured green, or green and
yellow.
Connect the blue (neutral)
wire to the terminal in the
plug which is marked with
the letter «N» or coloured
black.
Connect the brown (live)
wire to the terminal which is
marked with the letter «L» or
coloured red.
The plug moulded on to the
cord incorporates a fuse. For
replacement, use a 13 Amp
BS 1362 fuse.
Only ASTA approved fuses
should be used.
The fuse cover/carrier must
be replaced in the event of
changing fuse.
The right fuse cover/carrier
colour is the one shown by
the coloured insert at the
base of the plug.
The plug must not be used
if the fuse cover/carrier is
lost.
A replacement cover/car¬
rier must be obtained from
Zanussi
Service
Agents
whose addresses are listed on
the attached «Zanussi Service
Force Directory* or you could
find your local agent by looking
in your telephone directory
under "Z".
This appliance complies with
E.E.C. directive no. 87/308 of
2.6.87 relative to radio inter¬
ference suppression.