Zanussi ZT 605 지침 책자 - 페이지 4

{카테고리_이름} Zanussi ZT 605에 대한 지침 책자을 온라인으로 검색하거나 PDF를 다운로드하세요. Zanussi ZT 605 15 페이지. Dishwashers
Zanussi ZT 605에 대해서도 마찬가지입니다: 지침 책자 (16 페이지), 지침 책자 (20 페이지)

페이지 인쇄

INSTALLATION

Remove all packaging before positioning the ma¬

chine.

Positioning

If possible, position the machine next to a water tap

and a drain.

The sides and the back of the dishwasher can rest

against the adjacent furniture or the wail.

The dishwasher features fill and drain hoses which can

be turned either to the left or the right to suit the instal¬

lation.

Levelling

Good levelling is essential for correct closure and

sealing of the door.

Loosen or tighten the adjustable support feet, until the

machine is perfectly level.

Water Outlet Connection

The end of the drain hose can be connected as follows:

to the sink outlet siphon, securing it if necessary with a

clip;

to a wall outlet provided with vent-hole, minimum

internal diameter 4 cm;

hooked over the edge of the sink using the special

curved plastic guide provided.

The waste connection must be at a height of between

30 cm (minimum) and 100 cm (maximum) from the

floor.

It makes no difference which way the drain hose faces,

either to the right or left of the dishwasher.

Avoid bending or kinking the hose as this could

prevent or slow down the discharge of water.

If you use a drain hose extension it must be no longer

than 2 metres and its internal diameter must be no

smaller than the diameter of the hose provided.

Likewise the internal diameter of the couplings used

for connection to the waste outlet must be no smaller

than the diameter of the drain hose.

Water Supply Connections

This dishwasher may be fed with either hot (max. 60°C)

or cold water.

A hot water supply is not always efficient with very

soiled crockery as it shortens the washing

programmes a lot.

Feeding the appliance with a hot water supply (max.

60°C) will allow you to obtain considerably shorter

programmes.

For making the connec¬

tion itself, the coupling nut

fitted to the machine's

supply hose is designed

to screw onto either a 3/4

inch gas thread spout, or

to a purpose made quick¬

coupling tap such as the

Press-Block. To make this

easier, the hose itself may

be turned to the left or the right. In either case, be sure

to incorporate the strainer (A) supplied with the

machine onto the joint. See picture.

The water pressure must be within the limits given in

the technical specifications, as it will not function

correctly if pressure is outside these specifications.

Caution: the retaining ring must be properly fitted so

as to avoid water leaks.

Note: the end of the hose

connected to the ma¬

chine can be positioned

as required, by simply

slackening the retaining

ring.

Re-tighten the ring secure¬

ly to avoid water leaks.

Avoid bends or kinks in the hose, which could prevent

or slow down the flow of water.

If the machine is connected to new pipes or pipes

which have not been used for a long time, you are

advised to run the water for a few minutes before

connecting the inlet hose. This will prevent deposits of

sand or rust clogging the inlet hose filter.

Electrical connection

Before plugging the appliance into the wall socket,

make sure that;

1. the mains voltage corresponds to the voltage given

in the technical specifications;

the meter, fuses, mains power supply and wall

socket can all take the maximum load required.

Make sure that the socket and plug are compatible

without having to use any type of adapter. If necessary,

have the domestic wiring system socket replaced.

Safety standards require the appliance to be

earthed.

The Manufacturer accepts no liability for failure to

fkc ohm/o cnfpfv

nrprautions.