Zanussi ZGF 782 지침 책자 - 페이지 18
{카테고리_이름} Zanussi ZGF 782에 대한 지침 책자을 온라인으로 검색하거나 PDF를 다운로드하세요. Zanussi ZGF 782 19 페이지. Hob zanussi
Zanussi ZGF 782에 대해서도 마찬가지입니다: 지침 책자 (20 페이지), 지침 책자 (19 페이지), 지침 책자 (20 페이지), 지침 책자 (20 페이지), 지침 책자 (19 페이지)
![Zanussi ZGF 782 지침 책자](/uploads/products/server2/7124247/7124247.png)
Servicing
A: Removal Of Hob Top
1. Remove all control knobs, pan supports, burner caps
and burner crowns.
2. Remove 2 screws for each burner.
3. Remove 6 fixing screws from the pan support hinges,
and remove the hinges from the hob.
4. Lift hob top at the rear and disengage it from the
front locators.
B: Removal Of the Hob Taps
(Isolate Electrical Supply)
1. Follow the procedures in Section A.
2. With the aid of a 7mm spanner remove the clamping
bolt from the fixing clamp.
3. Loosen the pipe connection nut from the gas tap with
the aid of a 16mm spanner. Remove fixing clamps.
4. Reassemble in reverse order and carry out leak test.
C: Removal Of Mains Terminal Block
(Isolate Electric Supply)
1. Follow the procedures in Section A.
2. Disconnect supply flex connections from terminal
block.
3. From the underside of the hob remove 1 self tapping
screw from the terminal block.
4. Reassemble in reverse order.
Conversion from Natural Gas to LPG
It is important to note that this model is designed for
use with natural gas but can be converted for use with
butane or propane gas providing the correct injectors
are fitted. The gas rate is adjusted to suit.
Method
• Ensure that the gas taps are in the 'OFF' position
• Isolate the hob from the electrical supply
• Remove all pan supports, burner caps, rings, crowns
and control knobs.
• With the aid of a 7mm box spanner the burner
injectors can then be unscrewed and replaced by the
appropriate LPG injectors.
D: Removal Of Burner
1. Follow the procedures in Section A.
2. With the aid a 12mm spanner loosen off the pipe
connection nut.
3. From the underside of the hob remove 2 self tapping
screws from the burner body.
4. Reassemble in reverse order and carry out leak test.
E: Removal of Ignitor
(Isolate Electrical Supply)
1. Follow the procedures in Section A.
2. Remove H.T. leads from the ignitor by pulling tab
connection off. Disconnect supply cable from the
ignitor unit.
3. With the aid of a pair of thin nose pliers, pull the
spring clip sideward off of the underside of the
ignitor
4. Reassemble in reverse order.
F: Removal of Ignitor Switch
(Isolate Electric Supply)
1. Follow the procedures in Section A.
2. Remove the fixing nut from the switch and remove
tab connections.
3. Reassemble in reverse order and check with wiring
diagram for correct reconnection.
TO ADJUST THE GAS RATE
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw, which is
located down the centre of the gas tap control shaft.
Upon completion stick the replacement rating plate
on the under side of the hob.
IMPORTANT
The replacement/conversion of the gas hob should
only be undertaken by a competent person.
19