Zanussi ZGF 786 ICX 지침 책자 - 페이지 8
{카테고리_이름} Zanussi ZGF 786 ICX에 대한 지침 책자을 온라인으로 검색하거나 PDF를 다운로드하세요. Zanussi ZGF 786 ICX 11 페이지.
Zanussi ZGF 786 ICX에 대해서도 마찬가지입니다: 운영 및 설치 매뉴얼 (13 페이지)
페이지 인쇄
Adaptation to different types of gas
Injectors replacement
•
Remove the pan supports.
•
Remove the burner's caps and crowns.
•
With a socket spanner 7 unscrew and remove the
injectors (Fig. 7), and replace them with the ones
required for the type of gas in use (see Table 2).
•
Reassemble the parts, following the same procedure
backwards.
•
Replace the rating label (placed near the gas supply
pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.
Should the feeding gas pressure be different or variable
compared with the required pressure, an appropriate
pressure adjuster must be fitted on the gas supply pipe,
in compliance with the rules in force.
Adjustment of minimum level
To adjust the minimum level of the burners, proceed as
follows:
•
Light the burner.
•
Turn the knob on the minimum position.
•
Remove the knob.
•
With a thin screwdriver, adjust the by-pass screw
positioned in the centre of the gas tap control shaft
(see Fig. 6). If changing from natural gas 20 mbar to
liquid gas, completely tighten the adjustment screw
in. If changing from liquid gas to natural gas 20 mbar,
undo the by-pass screw about 1/4 of a turn. If changing
from natural gas 20 mbar to natural gas 13 mbar undo
the by-pass screw about 1/4 of a turn. If changing from
liquid gas to natural gas 13 mbar, undo the by-pass
screw about 3/4 of a turn.
•
Finally check the flame does not go out when quickly
turning the knob from the maximum position to the
minimum position.
This procedure can easily be carried out, anyhow the
hob has been positioned or built in the working top.
TYPE
TYPE OF
OF GAS
BURNER
Ultra-rapid (large)
NATURAL
Rapid (large)
GAS
Semi-rapid (medium)
G 20
Auxiliary (small)
Ultra-rapid (large)
LPG
Rapid (large)
(Buthane/
Semi-rapid (medium)
Propane)
Auxiliary (small)
Ultra-rapid (large)
NATURAL
Rapid (large)
GAS
Semi-rapid (medium)
G 20
Auxiliary (small)
8
INJECTORS
NOMINAL
MARKS
POWER
1/100 mm
INPUT
KW
146
4,00
113
2,80
96
2,00
70
1,00
98
4,00
86
2,80
71
2,00
50
1,00
146
3,00
108
2,13
105
1,72
80
0,90
FO 0392
Fig. 7
Fig. 8
By-pass screw
Table 1 : BY-pass diameters
Burner
Auxiliary
Semi-rapid
Rapid
Ultra rapid
REDUCED
POWER
kW
m
1,20
0,381
0,65
0,267
0,45
0,190
0,33
0,095
1,20
0,65
0,45
0,33
1,20
0,285
0,52
0,210
0,42
0,186
0,30
0,085
Ø By-pass
in 1/100
of mm.
28
32
40
56
Table 2: Injectors
NOMINAL
NOMINAL
POWER
PRESSURE
mbar
3
/h
g/h
-
-
-
20
-
-
291
-
204
-
145
30/30
-
73
-
-
-
13*
-
* for Russia only.