Zanussi ZGG75XS524 사용자 설명서 - 페이지 11

{카테고리_이름} Zanussi ZGG75XS524에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Zanussi ZGG75XS524 21 페이지.

페이지 인쇄

If there are other fuel burning appliances in the

same room, B.S. 5440 Part 2 Current Edition,

should be consulted to determine the requisite air

vent requirements.

For appliances installed in the Republic of Ireland

please refer to the NSAI- Domestic Gas Installation

I.S. 813 Current Editions Table Four.

Location

The hob may be located in a kitchen, a kitchen/

diner or bed sitting room (with a volume greater

than 20 m³), but not in a bathroom or shower room.

The minimum distance combustible material can be

fitted above the hob in line with the edges of the

hob is 400 mm. If it is fitted below 400 mm a space

of 50 mm must be allowed from the edges of the

hob.

For appliances installed in the Republic of Ireland

please refer to NSAI- Domestic Gas Installation I.S

813 Current Edition Section 7- Permitted

Locations of Appliance.

GAS CONNECTION

WARNING! Any gas installation must

be carried out by a GAS SAFE

Make sure that, once the hob is installed, it is easily

accessible for the engineer in the event of a

breakdown.

The manufacturer will not accept liability, should the

above instructions or any of the other safety

instructions incorporated in this instruction booklet

be ignored.

On the end of the shaft, which includes the R 1/2"

threaded elbow, adjustment is fixed so that the

washer is fitted between the components as shown

in the diagram. Screw the parts together without

using excessive force.

B C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

Connection to the gas supply should be with either

rigid or semi-rigid pipe, i.e. steel or copper.

The connection should be suitable for connecting

to R 1/2 (1/2 BSP male thread).

When the final connection has been made, it is

essential that a thorough leak test is carried out on

the hob and installation.

Make sure that the main connection pipe does not

exert any strain on the hob.

If you use flexible metal pipes make sure that they

agree to ISO 10380 and ISO 10807 standards. Be

careful they do not come in touch with mobile parts

or they are not squeezed. Also be careful when the

hob is put together with an oven.

CAUTION! It is important to install the

elbow correctly, with the shoulder on

the end of the thread, fitted to the hob

connecting pipe.

CAUTION! Failure to ensure the

correct assembly will cause leakage of

gas.

CAUTION! Make sure that the gas

supply pressure of the appliance

obeys the recommended values.

Rigid connection:

Carry out connection by using metal rigid pipes

(copper with mechanical end).

INJECTORS REPLACEMENT

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors

and replace them with the ones which are

necessary for the type of gas you use (see

table in "Technical Information" chapter).

4. Assemble the parts, follow the same procedure

backwards.

5. Replace the rating plate (it is near the gas

supply pipe) with the one for the new type of

gas supply. You can find this plate in the

package supplied with the appliance.

If the supply gas pressure is changeable or

different from the necessary pressure, you must fit

an applicable pressure adjuster on the gas supply

pipe.

ADJUSTMENT OF MINIMUM LEVEL

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the knob.

4. With a thin screwdriver, adjust the bypass

screw position (A).