Zanussi ZGG96624XA 사용자 설명서 - 페이지 5

{카테고리_이름} Zanussi ZGG96624XA에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Zanussi ZGG96624XA 16 페이지. Zanussi cooktop user manual

페이지 인쇄

Important! Failure to ensure the correct assembly will

cause leakage of gas.

Important! Make sure that the gas supply pressure of the

appliance obeys the recommended values.

Rigid connection:

Carry out connection by using metal rigid pipes (copper

with mechanical end).

Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the burner.

3. With a socket spanner 7 remove the injectors and re-

place them with the ones which are necessary for the

type of gas you use (see table in Technical Data sec-

tion).

4. Assemble the parts, follow the same procedure back-

wards.

5. Replace the rating label (it is near the gas supply

pipe) with the one for the new type of gas supply. You

can find this label in the package of the injectors sup-

plied with the appliance.

If the supply gas pressure is changeable or different from

the necessary pressure, you must fit an applicable pres-

sure adjuster on the gas supply pipe.

Adjustment of minimum level

To adjust the minimum level of the burners:

1. Light the burner.

2. Turn the knob on the minimum position.

3. Remove the control knob.

4. With a thin screwdriver, adjust the by-pass screw po-

sition. If you change from natural gas 20 mbar to liq-

uid gas, fully tighten the adjustment screw in. If you

change from liquid gas to natural gas 20 mbar, undo

the by-pass screw approximately 1/4 of a turn.

Minimum adjustment screw

5. Make sure the flame does not go out when you quick-

ly turn the knob from the maximum position to the

minimum position.

Electrical connection

• Any electrical work required to install this hob should

be carried out by a qualified electrician or competent

person, in accordance with the current regulations.

• THIS HOB MUST BE EARTHED.

• Always use a correctly installed shockproof socket.

• Make sure that there is an access to the mains plug af-

ter installation.

• Do not pull the mains cable to disconnect the appli-

ance. Always pull the mains plug.

• The appliance must not be connected with an extension

cable, an adapter or a multiple connection (risk of fire).

Check that the ground connection is in conformity with

the standard and regulations force.

• The power cable must be placed in such a way that it

does not touch any hot part.

• Connect the appliance to the mains with a device that

lets to disconnect the appliance from the mains at all

poles with a contact opening width of minimum 3 mm,

eg. automatic line protecting cut-out, earth leakage

trips or fuse.

• None of a parts of the connection cable can not get a

temperature 90°C.

Electrical Requirements

Any permanent electrical installation must comply with the

latest I.E.E. Regulations and local Electricity Board regula-

tions. For your own safety this should be undertaken by a

qualified electrician, e.g. your local Electricity Board, or a

contractor who is on the roll of the National Inspection

Council for Electrical Installation Contracting (NICEIC).

The manufacturer declines any liability should these safety

measures not be observed.

This hob is designed to be connected to a 230 V 50 Hz AC

electrical supply.

Before switching on, make sure the electricity supply volt-

age is the same as that indicated on the hob rating plate.

The rating plate is located on the bottom of the hob.

The hob is supplied with a 3 core flexible supply cord in-

corporating a 3 amp plug fitted. In the event of having to

change the fuse, a 3 amp ASTA approved (BS 1362) fuse

must be used.