Blackberry RAP40GW 안전 및 제품 정보 - 페이지 6

{카테고리_이름} Blackberry RAP40GW에 대한 안전 및 제품 정보을 온라인으로 검색하거나 PDF를 다운로드하세요. Blackberry RAP40GW 10 페이지. Wireless handheld
Blackberry RAP40GW에 대해서도 마찬가지입니다: 시작하기 매뉴얼 (2 페이지)

페이지 인쇄

Safety and Product Information

Cleaning: Do not use liquid, aerosol cleaners, or solvents on or near the device or device accessory. Clean only with a

soft dry cloth. Disconnect any cables from the computer and unplug any charging accessories from the electrical outlet

before cleaning either the device or the charging accessory.

Compliance information

Exposure to radio frequency signals

The BlackBerry device radio is a low power radio transmitter and receiver. When the device radio is on, it receives and

also sends out RF signals. The device complies with FCC, Industry Canada (IC), and Council of the European Union (EU)

guidelines respecting safety levels of RF exposure for wireless devices, which in turn are consistent with the following

safety standards previously set by Canadian, U.S., and international standards bodies:

• ANSI/IEEE C95.1, 1999, IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency

Electromagnetic Fields, 3 kHz to 300 GHz

• National Council on Radiation Protection and Measurements (NCRP) Report 86, 1986, Biological Effects and

Exposure Criteria for Radio Frequency Electromagnetic Fields

• Health Canada, Safety Code 6, 1999, Limits of Human Exposure to Radio Frequency Electromagnetic Fields in the

Frequency Range from 3 kHz to 300 GHz

• EN 50360, 2001, Product standard to demonstrate the compliance of mobile phones with the basic restrictions

related to human exposure to electromagnetic fields (300 MHz to 3 GHz)

• International Commission on Non-Ionizing Radiation Protection (ICNIRP), 1998, Guidelines for limiting exposure to

time-varying electric, magnetic, and electromagnetic fields (up to 300 GHz)

• Official Journal of the European Union, 1999, Council Recommendation of 12 July 1999 on the limitation of

exposure of the general public to electromagnetic fields (0 Hz to 300 GHz)

To maintain compliance with FCC, IC, and EU RF exposure guidelines when carrying the device on your body, use only

RIM-supplied or approved accessories. Use of accessories that are not expressly approved by RIM might violate FCC, IC,

and EU RF exposure guidelines and might void any warranty applicable to the device. When carrying the device while

the device radio is on, use the specific RIM-approved holster that has been tested for compliance. For data operation

(when you do not use a RIM-approved, body-worn accessory and are not holding the device at the ear), position the

device at least 15mm (0.60 inches) from the body.

Specific absorption rate data

THIS WIRELESS DEVICE MODEL MEETS GOVERNMENT REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.

The BlackBerry device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission

limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S.

Government, Industry Canada of the Canadian Government (IC), and recommended by The Council of the European

Union. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general

population. The guidelines are based on standards that were developed by independent scientific organizations

through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin

designed to assure the safety of all persons, regardless of age and health.

The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or

SAR. The SAR limit set by the FCC/IC is 1.6W/kg*. The SAR limit recommended by The Council of the European Union

is 2.0W/kg**. Tests for SAR are conducted using standard operating positions specified by the FCC/IC with the device

transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the

highest certified power level, the actual SAR level of the device while operating can be well below the maximum value.

This is because the device is designed to operate at multiple power levels so as to use only the power required to reach

the network. In general, the closer you are to a wireless base station antenna, the lower the power output.