Directed Xpresskit DBALL2 설치 매뉴얼 - 페이지 7

{카테고리_이름} Directed Xpresskit DBALL2에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Xpresskit DBALL2 13 페이지. Ford5 remote start ready (rsr) installation
Directed Xpresskit DBALL2에 대해서도 마찬가지입니다: 설치 매뉴얼 (12 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 매뉴얼 (14 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (15 페이지), 설치 및 빠른 참조 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 매뉴얼 (19 페이지)

페이지 인쇄
Directed Xpresskit DBALL2 설치 매뉴얼
Platform: DBALL2
Firmware: CHRYSLER6
Module Reset
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
D2D Installation
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
OR
1
W2W Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
Wait 3 seconds until the LED turns ON solid orange then release the
2
programming button. The LED then turns ON solid red.
Hard Reset
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
D2D Installation
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
OR
1
W2W Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds
2
until the LED starts to flash orange and red.
3
Release the programming button. The LED turns ON solid red.
rd
3
th
5
st
2
1
th
4
st
2
1
&
Solid
rd
3
th
5
st
2
1
th
4
st
2
1
© 2015 Directed. All rights reserved.
Rev.: 20151029
Page 7
nd
th
4
nd
rd
3
&
Release
Solid
nd
th
4
nd
rd
3
&
Solid
Flashes
&
Release
Solid