Directed Xpresskit DBALL2 설치 매뉴얼 - 페이지 12

{카테고리_이름} Directed Xpresskit DBALL2에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Xpresskit DBALL2 15 페이지. Ford5 remote start ready (rsr) installation
Directed Xpresskit DBALL2에 대해서도 마찬가지입니다: 설치 매뉴얼 (12 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 매뉴얼 (14 페이지), 설치 매뉴얼 (13 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 및 빠른 참조 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 매뉴얼 (19 페이지)

페이지 인쇄

Platform: DBALL2

Firmware:

NISS06

Remote Start Ready

LED

Description

External module synchronization

OBDII feature is not supported.

(Flashes red,

red then

orange) x 10

Activation Ground When Running (Status)

Flashes

Ground When Running (Status) command received.

green

Ignition ON command received.

Flashes red

& orange

Flashes

Start ON command received.

green

quickly

Flashes red

PTS shutdown error.

x 10

Flashes red

CAN bus incorrectly detected.

x 21

Commands

Flashes

LOCK command received.

orange x 1

Flashes

UNLOCK command received.

orange x 2

Flashes

TRUNK command received.

orange x 3

Flashes

AUX1 command received.

orange x 4

Flashes

AUX2 command received.

orange x 5

Flashes

AUX3 command received.

orange x 6

Shutdown codes

Flashes

Takeover successful.

green x 1

Flashes red

Runsafe was not disabled.

x 1

Flashes red

Brake was not detected.

x 2

Flashes red

Smart key was not detected.

x 3

Flashes red

Speed was detected.

x 4

RSR codes

3x OEM Lock Remote Start Activation was attempted

Flashes red

x 7

when RFTD feature is disabled.

Flashes red

Feature error.

x 9

(RSR)

Installation

Troubleshooting

The diagnostic data bus was not detected, therefore the

SmartStart features will be limited.

The module has initialized the remote start sequence.

The module has received the Ignition ON command and

is processing the remote start sequence.

The module has received the Start ON command and is

processing the remote start sequence.

The PTS output from the module was not activated due

to safety protection.

Verify the CAN1 and CAN2 connections. Refer to

"Installation (wiring diagrams & vehicle wiring reference

charts)" to check the connections.

If the bypass module fails to flash, it did not receive the

signal. Commands can come from RF or D2D.

Normal operation.

No UNLOCK command was received prior to opening the

door, or the 45 second timer expired in takeover mode.

The brakes were not detected, which prevents the

system from shutting down the vehicle.

The smart key was not detected, which prevents the

system from shutting down the vehicle.

The vehicle was detected as moving, which prevents the

system from shutting it down.

Activated from Web automatically when using RSR flash

tool or can be done manually. Refer to feature

programing section for more information.

An RSR feature file mismatch was detected. Please

contact Technical Support.

Rev.: 20

1707

Page 12