Directed Xpresskit DBALL2 설치 및 빠른 참조 매뉴얼 - 페이지 8

{카테고리_이름} Directed Xpresskit DBALL2에 대한 설치 및 빠른 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Xpresskit DBALL2 16 페이지. Ford5 remote start ready (rsr) installation
Directed Xpresskit DBALL2에 대해서도 마찬가지입니다: 설치 매뉴얼 (12 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 매뉴얼 (14 페이지), 설치 매뉴얼 (13 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (15 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 매뉴얼 (19 페이지)

페이지 인쇄
Directed Xpresskit DBALL2 설치 및 빠른 참조 매뉴얼
Platform: DBALL2
Firmware: GM6
Installation Type 3d, T-Harness THGM610 Rev. 3, T-02 (without RFLCHGM)
WARNING!
We recommend using the Wiring Diagram (
RFLCHGM) will draw 15-20mA more on the vehicle, when it is parked and the engine is turned off.
Using the Wiring Diagram (
wire opening. To preserve OEM remote starter functionality, use the Wiring Diagram (
Use connectors
D2D
labeled GM6
only
Ignition
Barrel
To vehicle
6-pin connector
T-02
Cadillac Escalade
Chevrolet Avalanche
Chevrolet Express Van
Chevrolet Silverado 1500
Chevrolet Silverado 2500/3500
Chevrolet Suburban
Chevrolet Tahoe
GMC Savana
GMC Sierra 1500
GMC Sierra 2500/3500
GMC Yukon
Hummer H2
If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
[1]
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid the issue. RAP Off: Refer to page 9 for wire color and location.
Only required if no OEM hood pin.
[2]
with
RFLCHGM) on page 3, especially if the vehicle is not used daily. The Wiring Diagram (
without
RFLCHGM) can deactivate OEM remote starter functionality, OEM fob and smart phones, due to the accessory
To
Immobilizer
Control
Module (ICM)
(under ignition switch,
black connector)
GM06
Ignition
(+) Ignition Status Output: Pink:7
Connector
n/a: Black/White:1
(-) RAP Off: Green/Black:2
[1]
NOT
n/a: Violet/Brown:8
USED
n/a: Violet/Green:9
T-01
(-) Driver
Door Sense
Trigger
[1]
T-02
with
RFLCHGM) on page 3.
(+) Ignition Input
To
Immobilizer
Control
Module (ICM)
(vehicle side)
RF
Prog.Button
LED
T-Harness
THGM610
GM10
(Optional)
CAN High
Single Wire CAN:
Dk.Green pin 1
SW CAN
CAN Low
Rev.: 20151221
without
(-) Ground
(-) Ground
(+) 12V
(+) 12V
(-) Hood Status Input
[2]
Hood Pin
(-) Parking Lights
(-) Parking Lights
n/a: White/Black
Remote Start Safety
Override Switch
(+) 12V
DBALL/
RX
(-) Ground
DBALL2
P#: XKD2D65
TX
NOT USED
CAN High: Tan/Black, pin 6
Diagnostic
connector
1
8
OBDII
9
16
(connector side view)
CAN Low: Tan, pin 14
© 2015 Directed. All rights reserved.
Page 8