Directed Xpresskit DBALL2 설치 매뉴얼 - 페이지 10

{카테고리_이름} Directed Xpresskit DBALL2에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Xpresskit DBALL2 16 페이지. Ford5 remote start ready (rsr) installation
Directed Xpresskit DBALL2에 대해서도 마찬가지입니다: 설치 매뉴얼 (12 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (18 페이지), 매뉴얼 (14 페이지), 설치 매뉴얼 (13 페이지), 설치 매뉴얼 (14 페이지), 설치 매뉴얼 (19 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (20 페이지), 설치 매뉴얼 (15 페이지), 설치 및 빠른 참조 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 설치 매뉴얼 (16 페이지), 설치 매뉴얼 (18 페이지), 매뉴얼 (19 페이지)

페이지 인쇄
Directed Xpresskit DBALL2 설치 매뉴얼
Platform: DBALL2
Firmware:
CHRYSLER4

Module Reset

A module reset will erase the module programming
configured on the module using the web
D2D Installation
If required for your installation, c
14-pin harnesses to the module Press
p
rogramming button
OR
1
W2W Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module Press
button, then connect the 14-pin harness to the module.
Wait 3 seconds until the
2
p
rogramming button.

Hard Reset

Warning gainst xecuting a Hard Reset!
A
E
A hard reset will erase all the data stored in the
default values. After a hard reset, you may have to reconfigure your
not part of the default configuration. See the
D2D Installation
If required for your installation, c
14-pin harnesses to the module Press
p
rogramming button
OR
1
W2W Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module Press
button, then connect the 14-pin harness to the module.
Wait 3 seconds until the
2
until the
LED starts to flash orange
3
Release the programming button. The
only
config
tool will remain untouched
onnect the 10-pin 12-pin
.
and
hold the
, then connect the 4-pin D2D harness.
.
and
hold the rogramming
p
LED turns
ON
solid
orange then release the
The
LED
then turns
ON
solid red.
DBALL
and will change all the settings configured on the module to its
Feature & Option List
onnect the 10-pin 12-pin
.
and
hold the
, then connect the 4-pin D2D harness.
.
and
hold the rogramming
p
LED turns
ON
solid
orange
and
red.
LED
turns
(bypass, convenience and vehicle detection). All the settings
.
,
&
th
5
st
1
st
1
DBALL
if your installation requires specific options,
section of this guide.
,
&
th
5
st
1
st
1
, and w
ait
10 more seconds
ON
solid red.
Rev.: 20170818
Page 10
rd
3
nd
2
th
4
th
4
nd
2
rd
3
&
&
Solid
Release
Solid
rd
3
nd
2
th
4
th
4
nd
2
rd
3
&
Solid
Flashes
&
Release
Solid
© 2017 Directed. All rights reserved.