Acorn Meridian 3792 매뉴얼 - 페이지 12
{카테고리_이름} Acorn Meridian 3792에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Acorn Meridian 3792 12 페이지. Corterra ada-compliant washfountain
페이지 인쇄
REPAIR PARTS (CONTINUED)
Description
P-Trap
SOAP SYSTEM
Optional –DV Soap Tank
Soap Dispenser Pump
CARE, CLEANING, AND REPAIR OF CORTERRA SOLID SURFACE
Corterra should be kept clean at all times. If maintained, Corterra surfaces will retain their new, clean appearance
indefinitely. In order to remove any unwanted stains, wash with soapy water then rinse. In order to prevent water stains from
occurring, dry surface right after rinsing. If the stain persists, use a Scotch Brite pad and an abrasive cleaner, or you can also
use a solution consisting of household bleach and water (1 part water to 1 part bleach). To avoid any water marks, wipe surface
dry. To remove cuts and scratches use 400 grit sandpaper, followed by an abrasive cleaner and Scotch Brite pad. In order to
repair chipped Corterra (using repair kit available from Acorn) do the following:
•
Put on gloves prior to handling any of the materials in the kit, and ensure adequate ventilation.
•
Add contents of "B" (liquid resin) to larger container "A" (solid filler). Mix completely using wooden stick.
•
Add tube of "C" (liquid catalyst). Mix for two (2) minutes. CAUTION: Catalyst gel time at 75° is 15 minutes.
•
Apply mixed material to damaged area using wooden stick. NOTE: Apply only as much patch as required.
•
Let cure approximately 3-4 hours. NOTE: For a "fast cure" of approximately 10 minutes, use a lamp with a 100 watt light
bulb shining on patched area about 2-1/2" from patch.
•
Use coarse grained sandpaper to sand off extra material once patch is hard.
•
Use medium grained sandpaper for finer finish.
•
Use fine grained sand paper for "polished" look finish.
•
Discard extra patch material appropriately.
WARNING: Flammable. Keep away from heat, sparks, and open flame. Avoid contact with skin and wash with soap and water
after skin contact. In case of eye contact, flush with water for 15 minutes and get medical attention. Harmful if swallowed.
Keep out of reach of children.
CARE AND CLEANING OF STAINLESS STEEL SURFACE
Stainless steel should be kept clean at all times. If maintained, stainless steel surfaces will retain their new, clean, polished
appearance indefinitely. To remove water spots or rust spots, stainless steel cleaner/polish on a cloth is recommended. IF
SPOTS ARE STUBBORN OR IF YOU WISH TO TREAT A SCRATCH: synthetic, abrasive, general-purpose pads such as
Scotch Brite are recommended. Apply the stainless steel cleaner/polish to the synthetic, abrasive pad and CAREFULLY rub
out spot with cleaner/polish. Be sure to rub in the direction of the grain! Do not allow steel wool to come in contact with
stainless steel. Steel particles can embed into the stainless steel surface and create rust!
Acorn warrants that all of its products are guaranteed against defective material or poor workmanship for a period of one year
from date of shipment. Acorn's liability under this warranty shall be discharged by replacing without charge F.O.B. City of
Industry, California, any goods, or part thereof, which appears to the company upon inspection to be of defective material or not
of first class workmanship, provided that claim is made in writing to the company within reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be delivered to the company, prepaid, at City of
Industry, California for inspection. Acorn will not be liable for the cost of repairs, alterations or replacement, or for any expense
connected therewith made by the owner or his agents, except upon written authority from the Acorn City of Industry office. Acorn
will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as above
provided. Contact local Acorn Representative for complete terms and conditions.
L1000802
Part No.
4970-008-001
6214-006-001
6214-009-001
WARRANTY INFORMATION
12 of 12
Diagram
Rev. H – 03/07/05