Directed Electronics AutoCommand 40026 설치 매뉴얼 - 페이지 2

{카테고리_이름} Directed Electronics AutoCommand 40026에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Electronics AutoCommand 40026 20 페이지. Remote car starter

페이지 인쇄

Directed Electronics AutoCommand 40026 설치 매뉴얼

On cars with airbags, you may notice bright yellow tubes

or harnesses marked SRS (Supplemental Restraint Sys-

tem) underneath the steering column area. DO NOT tamper

with these wires in any way, to prevent personal injury

and/or damage to the air bag system.

On GM rear-wheel drive vehicles built prior to 1995 and

Dodge Dakota trucks built prior to 1996, see the last page

of this instruction manual.

Battery gases are explosive.

Do not smoke while working near the car's battery.

Note : : : : : Some installers connect a battery charger to the vehicle's

Note

battery during installation. This is fine, but it must be removed be-

fore running the vehicle under remote starter control.

When running the wires through the car's firewall, be sure

to protect them from sharp metal edges and from hot

surfaces on and around the engine.

INSTALLATION INSTRUCTIONS

1. Before You Start

Please read through the entire installation manual before beginning.

Always leave a window open to avoid locking your keys in your car.

IMPORTANT: After having read the entire manual, start the installation

by putting the yellow WARNING STICKER in the engine compartment.

Choose a surface that is clean and readily visible when the hood is

open.

This car is equipped with a remote control starting device.

Disable before working on car!

AVERTISSEMENT

Ce véhicule est équipé d'un systéme de démarrage a distance. Mettez-le

hors fonction avant d'eflectuer toute opération d'entretien ou de réparation!

POWER & IGNITION HARNESS

The remote starter module will be installed under the dash once all

wiring has been completed. Do not mount the module at this time!

You will need to check the red diagnostic LED light as the installation

progresses. Locate (or drill) a hole in the firewall to run the PURPLE

and GREEN wires of the Control Harness and the PINK wire of the

Power Harness into the engine compartment. The remaining short

wires stay in the passenger area. Leave about a foot of the wire

harness under the dash for ease of working and visual access to the

diagnostic light.

The Installation Information section of our website

www.designtech-intl.com is available 24 hours/day to provide

you with free, up-to-date vehicle wiring information for your par-

ticular vehicle.

Note: Always connect the Pink and Black wires before connecting any

of the other wires. Do not insert the fuse until step 11.

2. Black Wire (16 AWG) - Ground

Connect the BLACK wire to a very good, clean chassis ground in the

driver's kick panel area. Use the small ring terminal. (The thin metal

bracing around or beneath the dash board is not always adequate.)

3. Pink Wire (12 AWG) - Power (+12 Volts)

Connect the ring terminal at the end of the short PINK wire to the +12

Volt terminal of the battery. Run the long pink wire through the

firewall of your vehicle. Join the remaining ends of the power wire

together by soldering them. Tape with electrical tape to leave no

v5.3 (40026)

WARNING

exposed wires. Alternatively, you may wish to use the yellow butt

connector, but we recommend soldering. Wait to insert the 30 amp

green fuse into the holder until step 11.

Note: Failure to properly install the fuse holder and 30 amp fuse to the

pink wire to the battery voids all product warranties.

Ignition Key Diagram for Steps 4-7

The vehicle's wires are found coming off of

the key switch. Remove the panel under the

steering column to access these wires.

4. Blue Wire (14 AWG) - Ignition 1

Connect the BLUE wire to the ignition 1 wire of your vehicle. This wire

will measure +12 Volts on the test meter in the "run" and "start" posi-

tion, and is off in the "lock/off" and "accessory" positions.

5. Green (14 AWG) - Ignition 2

Connect the GREEN wire to the Ignition 2 wire in the vehicle. The

Ignition 2 wire can function in several different ways in your vehicle.

It is important to understand how it works. The Ignition 2 wire will

usually measure +12 Volts in the "run" position and is off (ground) in

the "lock/off" and "accessory" positions. In certain vehicles, it may

also show +12 Volts in the "Start" position or Ignition 2 may turn OFF

during "Crank" and turn back ON after the starter disengages. Care-

fully note the function of the Ignition 2 wire. If the Ignition 2 turns

OFF during "Crank", see Changing Ignition 2 Function in (section

21). If Ignition 2 stays ON during "Crank," no options need to be

changed. Please refer to our wire color information available at

www.designtech-intl.com

6. White Wire (14 AWG) - Accessory

Connect the WHITE wire to the accessory wire which is +12 Volts in the

"run" and "accessory" position, but off in the "start" and "off" posi-

tions. In most GM vehicles, connect the white wire to the orange wire

that is hot in "run" only.

7. Yellow (14 AWG) – Starter

Connect the YELLOW wire to the starter wire. This wire will measure

+12 Volts on the test meter in the "start" position only.

Note: Most Nissan vehicles have two starter wires. Connect both

starter wires of the vehicle to the YELLOW start wire of the remote

starter.

8. Dash-mount LED-On/0ff Control Switch

Connection of the LED-On/0ff Control Switch is mandatory. Do not

let the switch wires touch ground. Mount the control switch so that

it is easily seen and accessible. If a hole is to be drilled to route the

switch wire, make sure there is enough clearance behind and noth-

ing can be damaged by the drill. Use a 1/4" drill-bit for the mounting

hole. Plug the switch connector into the module just to the right of

the control harness. The LED will turn Red when the switch is turned

ON and the LED will turn Green when the switch is turned OFF.

CONTROL HARNESS

(ALL WIRES ARE THE SMALLER 18 AWG SIZE)

9. Purple Wire - Hood Pin Switch -

Control Harness

The hood pin switch MUST be installed

with the remote starter. It prevents op-

eration of the remote starter when the

hood is open and is used to initialize

and program the unit. Connect the

PURPLE wire to the hood pin switch us-

ing the red connector.

To Alarm

To Remote Starter

How to share a hood pin

switch with an alarm