Directed Electronics Ready Remote 23926 설치 매뉴얼 - 페이지 5
{카테고리_이름} Directed Electronics Ready Remote 23926에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Directed Electronics Ready Remote 23926 19 페이지. Remote control car starter
페이지 인쇄
Option #4
Normal
This option will add 100% more crank time to the NoTach™ starting feature.
Option #5
Normal Voltage Metering
This option is used in the "No-Tach" starting method when the alter-
nator does not turn on quickly after the vehicle is started.
Option #7
"Enable" Feature
This option cancels the "enable" mode safety feature. The "enable"
mode requires that the driver toggle the ON/OFF control swith "OFF"
then "ON" each time the driver removes the key from the ignition in
order to "enable" the vehicle for remote starter control. This feature
guards against undesired starting of the vehicle by remote control.
You must keep this option as enable on all GM rear-wheel drive and
Dodge Dakota vehicles manufactured prior to 1996.
Option #8
Normal
This option will turn the headlights on about 10 seconds after it sees
the key in the ignition position – and turn the headlights off when
the key is removed from the ignition. You must hook up the lights
wire in step 13 for the Daytime Running Lights option.
Programming An Option:
If you want the factory setting, DO NOTHING and skip this section. If
you want to change one or more of the features, TURN THE ON/OFF
CONTROL SWITCH TO THE "OFF" POSITION. Wait for the red LED
light to stop flashing, then continue with the following procedures:
A. For options 1-8: Push the white code button on the remote start
module. Each time you push the button the red LED light will
flash 1 to 8 times signifying at which feature you are (press it
once, the red LED light flashes once. Press it again and it will
flash twice. Press it again and it will flash three times, etc., to
show what feature you are at).
B. When you are at the feature level you desire, push the start
button on the transmitter for 1 second and the red LED light will
flash once to signify you are at the Option setting. You can push
the transmitter button again and it will flash twice to signify you
are at the Factory setting. Push the transmitter button again and
you will go back to the Option setting (1 flash).
C. You can choose to change another feature by starting over again
at Step A. or, in six seconds, the remote starter automatically
exits the programming mode (Three red LED light flashes).
D. When finished – switch the Control Switch back ON. The red
LED light will flash once.
21. Changing Ignition 2 Function
Many vehicles turn off the Ignition 2 wire while the starter is crank-
ing. In these vehicles it is very important to have the remote starter
copy the starting sequence of the key exactly; otherwise the vehicle's
computer may show a fault code. Our vehicle wiring database on our
website will help you determine the correct IGN 2 wire for your ve-
hicle.
To turn the thick GREEN Ignition 2 wire off during crank:
1. Unplug all wires and connections from the remote start module.
2. Open the case of the remote start receiver module.
3.
Look for the small IGN2 switch as shown in the following dia-
gram.
4. Move the IGN2 switch to the OFF position.
5. Close the case and plug in all of the wire connectors.
The remote starter will turn off Ignition 2 while the starter is crank-
ing.
© 2005 Directed Electronics, Inc.
Super Crank
Ignore Voltage Metering
No "Enable"
Daytime Running Lights
SPECIAL CASES
1) How to Use a Relay
Many of the optional steps require a relay to be hooked up. The most
common relay used for this type application is the Bosch type relay
(Radio Shack Cat.# 275-226). Use the diagram shown for a typical hookup.
If you have another relay then you need to know that pins 85 and 86 in
this diagram relate to the coils of the relay. Pin 30 is the 'common', and
pin 87 is the 'normally open' contact. If your relay has a pin 87A in the
middle it is the normally closed contact and is not used. (The diagram is
typical for alarm disable, horn, or Ignition 3 applications). Relays with
only four terminals, such as RS-275-226 will NOT work for reverse polar-
ity door locks or starter kill.
To supply +12 volt output
+12 V
87
From
Remote
30
85
Starter
86
(-)
To Vehicle's Accessory
2) Code Learning
Your transmitter is factory coded to the remote starter module with
over 16,000,000 different codes. The remote starter module can
learn the codes of up to 4 different transmitters. If you want to add
additional transmitters to the receiver or if it does not respond to
your transmitter - follow the steps below to teach the receiver the
transmitter code(s):
A. Turn the Control Switch ON.
B. B. B. B. B. Push the red "code learn" button to the right of the red LED light.
The red LED light and the dash lights come on for a second. (The
vehicles ignition and accessory wires come on).
C. C. C. C. C. Hold down the Start button on the transmitter until the red LED
light and the dash lights come on again for a second. The mod-
ule has now learned the transmitter code. Release the transmit-
ter button. The transmitter should be at least a few feet away
from the brain module when doing this.
D D D D D . . . . . To learn additional transmitters (up to 3 more), immediately
(within 5 seconds) push the start button on another transmitter
for a few seconds until the red LED light and the dash lights
come on for a second again.
E. E. E. E. E. Five seconds after the last time the transmitter was learned the
unit exits the code-learning stage. (The red LED light, ignition
and accessories flash 4 times).
Note: Teaching the module a new transmitter code will erase all pre-
5
To supply Ground (-) output
To Ground
87
From
Remote
+12 V
30
Starter
85
86
(-)
To Vehicle's Accessory
+12 V
v5.3 (2126)