alphatronics PSTN-2-IP GPRS 빠른 참조 매뉴얼 - 페이지 5

{카테고리_이름} alphatronics PSTN-2-IP GPRS에 대한 빠른 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. alphatronics PSTN-2-IP GPRS 12 페이지. Gprs

페이지 인쇄

Preparations

Before installing make sure the following components are present:



Security alarm system with analog dialer or Alphatronics control panel with RS-485 bus



12VDC power supply in the control panel (only applicable if the transceiver is powered

from the control panel)

Otherwise a net adapter can be used (art. code. 200079)



Router or switch with a free LAN connection



Working internet connection



Computer / laptop with Internet Explorer 6 or higher

or compatible browser.



Network cable and optional cross-over network cable for programming

Note: Internet Explorer 5.0 (or lower) is not supported!

Before installing make sure the following information is known:

The protocol that the analog dialer of the control panel transmits (only applicable if the



analog dialer is connected via the PSTN interface)

The IP address and registration port of the RC-4001 IP or RX-5000/8000 receiver in



the central station including the subscriber number.

The IP address, subnet mask and (local) Gateway that must be programmed into the



PSTN-2-IP (GPRS) when not using DHCP configuration in the Ethernet settings

Mounting

1. It is advisable to install the PSTN-2-IP (GPRS) in the enclosure of the control panel. If

this is a metal cabinet than it should be equipped with a proper grounding.

2. When the analog (PSTN) dialer of the control panel is still connected to the telephone

(or VoIP) line, remove the cable from the phone line.

3. If connection to the IP transceiver is done through the PSTN interface, connect the

cable from the analog dialer to the dialer terminal (CMK) of the PSTN 2 IP (GPRS)

transceiver. Note: the cable of the analog dialer must be shorter than 30 meters.

4. Then connect a network cable between the PSTN 2 IP (GPRS) and the router, the

transceiver can now be accessed via the internal network. Use the free Device

Discovery Tool (see www.alphatronics.nl) to detect Alphatronics IP devices on the

network.

5. It is also possible to connect directly to the PSTN-2-IP (GPRS) using a Cross-over

network cable (art. code. 003620) between the LAN port of the laptop and the PSTN-2-

IP (GPRS). Ensure that the laptop has a fixed IP address in the same range

(192.168.0.xx) as the PSTN-2-IP (GPRS). Set dipswitches 2 * and 3 ** to ON.

6. Finally connect the power supply to the PSTN-2-IP (GPRS).

dipswitch 2 to ON ensures that it is always possible be log-in to the web server with Username "admin" and no

Password needs to be entered. Also, the IP address of the PSTN 2 IP (GPRS) is temporarily set to

192.168.0.48 (http port 80). Dipswitch 2 can remain OFF if the Username, Password and the IP address of the

PSTN 2 IP (GPRS) is known.

dipswitch 3 to ON (default) ensures that the programming can be accessed / modified.

If dipswitch 3 is set to OFF then the webpage of the PSTN-2-IP (GPRS) is completely blocked and it is not

possible to get into the programming.

PSTN-2-IP & PSTN-2-IP GPRS Quick reference

,Mozilla FireFox, Google Chrome

Rev.1.0

01-11-2012

Page 5